Инструкция на Центральный кабельный пульт управления кондиционерами Sinclair серии SCM-30

Текст инструкции

1. Стр. 1 FULL DC INVERTER SYSTEMS

   CENTRAL CONTROLLER SCM-30 COMMERCIAL AIR CONDITIONERS SDV4, SDV5, FANCOILS

2. Стр. 2

   Original instructions

3. Стр. 4 INSTALLATION PART

   Installation & Owner‘s Manual 1

4. Стр. 5 1.1 Packing list and installation components

   1. Please check the packing list of the centralized controller,whether the components are complete. Name No. Quantity Remarks 1 Centralized controller 1 2 Cross-recessed head tapping screws 6 GB845/ST3.9*25-C-H(S) 3 Fastening plastic expansion pipe 6 Φ6*30 4 Installation & Operation Manual 1 5…

5. Стр. 6 1.2 Installation instructions

   Installation instructions 1) Connect 220VAC power to the L N terminals of the centralized controller directly. 2) Do not lay the signal wire and the power wire of the centralized controller in the same power wire pipe, there should be 300~500mm distance between two pipes. 3) The signal wire of…

6. Стр. 7 Insert the flathead screwdriver into the

   concave on the upper side of the box, and rotate slightly to open the upper cover(3 places). Fix the screws of the centralized controller （GB845/ST3.9*25） Base Dial code ON Address dial code Front cover Dial code position Address range ~ 00 ~ 15 Fig. 1.2 Installation diagram X Y E F1 F2 E FORCED ON…

7. Стр. 8 1.4 System wiring instruction

   Network air conditioner wiring diagram (two types for indoor unit: one is the main control board with an external network interface module; the other is the network interface module is built in the main control board). RS232 pin buckle: insert the COM port of computer One computer can connect 16…

8. Стр. 9 Note

   The RS485-to-RS232 module and the wires in the wiring diagram are used when the network system needs to connect with the computer only. One computer can connect with 16 centralized controllers at most, Namely the maximum of indoor units is 16X64=1024 ,that a network system can connect. The…

9. Стр. 10 1.6 System wiring instruction

   1) Wiring diagram of building net work airconditioning system. (b) (a) (a) The wiring system is good for communication,recommended (b) The wiring system is bad for communication,not recommended 2) System wiring diagram of centralized controller and indoor unit of air conditioner. Both of the…

10. Стр. 11 OPERATION PART

    Installation & Owner‘s Manual 8

11. Стр. 12 2.1 Function instructions

    1. Centralized controller is used for controlling and data querying of air conditioners in the network. Each centralized controller can be connected to maximum 64 indoor units, through 485 communication can to form an air conditioner LAN and realize the centralized controlling network in the air…

12. Стр. 13 2.3 Key words

    2.3.1 State indication 1. LED for state indication 1) Normal state ① On The LED will be on when any one of the following occur: a) In the centralized controller network, one or more air conditioners are under operating state. b) Through the centralized controller’s operation, when the centralized…

13. Стр. 14 of the centralized controller is connected, all air conditioners in the nerwork of the centralized

    controller will start up compulsorily. By default, they will run in the cooling mood. The startup and shutdown operations of the centralized controller and computer and all functional modules will be disabled (only the command of startup is sent to the air conditioner，without affecting operation of…

14. Стр. 15 2) Operation

    Can set the heating mode locking or cooling mode locking. Under mode locking state, if set the new mode locking, it must be unlocking first, then can operate the new mode locking. ① Can lock or unlock through the computer. ② Can operate by centralized controller. In the centralized controller…

15. Стр. 16 1) One or more air conditioners under ON state (include timing process of timing ON

    and OFF) “ ” key only has short press function. Only send the OFF order to the air conditioners with ON state, not for OFF state units. The memory function is activated, the current state of all air conditioners is memorized. 2) All the air conditioners in the centralized controller network are OFF…

16. Стр. 17

    Installation & Owner‘s Manual the centralized controller press the “Reset”key five seconds to reset TIME OFF SET In the setting page, shift to the timing startup/shutdown setting page. RESET OK TIME ON FAN LOCK SWING DEC INC 1 In the setting page, set the temperature，increase or decrease the time of…

17. Стр. 18 2.4.1 Key operaion instruction

    1. Query key “ ” Any time when you press the key, the selected operation mode is to query the operation status of the air conditioner. By default, the first in-service air conditioner will be queried. 2. Set key “ ” In other display mode,press the key “ ” to enter the setting mode. By default, it is…

18. Стр. 19 9. Rightward key “

    ” In the query mode, when the key is pressed, the next in-service air conditioner is selected,and its operation status data will be displayed.If it is currently on the last air conditioner, the first one is selected and its data displays, when the key is pressed. If this key is hold down long, the…

19. Стр. 20 13. Reduce key “

    ” 1) Query mode Press this “ ” key, display the data of the previous page. If it is now in the first page, press the key “ ” again and the last page will be displayed. 2) Setting operation mode ① Temperature adjusting method Press this key “ ”, the setting temperature will decrease one degree. If…

20. Стр. 21 Hour

    Indoor temperature Computer communication Function module communication SMS modeule mommunication Fig.2.3 Mode selection: Auto, cooling,heating Fan speed Timing ON/OFF mark Temperature parameter Cooling mode locking Heating mode locking Remote controller locking Key locking Ventilation Electric…

21. Стр. 22 2.4.2 LCD instruction

    1. General display data 1） General display data is displayed in all display pages. ①The icon displayes when the centralized controller communicates with the computer or gateway normally, otherwise, it does’t display. ②The icon displayes when the centralized controller communicates with the…

22. Стр. 23 a. The array of the liquid crystal display is composed of 4X16 grids, and each grid is

    composed of two blocks of different sizes (as shown in the above figure). The status indication table is as follows： Status Object Constantly on Slow blink Big black block In-service Selected Small black block Power on Fast blink Not bright Out of service Fault of indoor/ outdoor unit Power off b.…

23. Стр. 24 2) Description of the query page

    Fig 2.6 The example diagram of the query page ①The LCD display shows the query page, and the air conditioner with the address of 01 is being queried. ②Mode of the air conditioner with the address 01 is: Cooling, strong air, swing on, indoor temperature 22°C,set temperature 20°C, cooling mode “lock”.…

24. Стр. 25 4) Fault page display description

    Fig 2.8 The example diagram of fault page ①Query the air conditioner with the address of 08 in the query page. ②The air conditioner with the address of 08 is faulty, and fault code is 08. The big black dot below (00+,08) blinks. ③In the array,only the big and small black dots at (00+,00) and…

25. Стр. 26

    00+ 16+ 32+ 48+ a. Function selection b. Parameter selection c. Reminding d. “Set successfully” reminding Fig 2.9 Filter net in addition to the dust function involves of show a contents 2) Function setting ① Dial the dial code 3 to “ON”, select the “Has optional function”referring to table 2.1 to…

26. Стр. 27 2.4.4 Fault and protection code table

    Fault code EF EE ED EC EB EA E9 E8 E7 E6 E5 E4 E3 E2 E1 E0 07# 06# 05# 04# 03# 02# 01# 00# Protection code PF PE PD PC PB PA P9 P8 P7 P6 P5 P4 P3 P2 P1 P0 Fault content Other faults Water level detection faults Reserved Cleaning fault Inverter module protection Over-current of compressor(4 times)…

27. Стр. 28 2.5 Technical indices and requirements

    1. EMC, EMI comply with the CE certification requirements. 2. Electrical safety comply with GB4706.32-2004, GB/T7725-2004. Installation & Owner‘s Manual 25

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.