Инструкции на Центробежные вентиляторы Rosenberg
Центробежные вентиляторы Rosenberg серии TRE / TRZ / HRE / HRZ с ременным приводом. Инструкция по эксплуатации.
Загружаем документ…
Текст инструкции
-
/ SAFETY / Industrial Safety Symbols . The following symbols refer to particular dangers or give advice for safe opreation. ! ! ! ! " Caution! Danger! Safety Advise # $ % % ! " Danger from electric current or high voltage! # ! " Crush Danger & " ! ! & % '( % % ) & #! Danger! Do not step under…
-
# $ - ' & & ' " % , & $ -! Before installing and operating modular units please, read instructions carefully! - − , , ( - , ! !) − ,# " , , ! − ( . .) - ! • Put the fan and other components to use only after they have been securely mounted and fitted with protection guards to unit application…
-
- 30 °C + 40 °C 95 % − min - 30°C ! - max + 40°C ! ! Radial fans with standard motor are suitable for ventilation of - clean air - slightly dusty and greasy air - slightly aggressive gases and vapour - mediums up to an atmospheric density of 1,3 kg/m3 - mediums with a temperature of -30°C up to…
-
− avoid distortion of the casing or other damages
• Use suitable assembling means as e.g. scaffolds conforming to specifications & " !! & % '( % % #! ) & Danger ! Do not step under hanging loads! 5. 2 / INSTALLATION 0 0 " & # '$ & - " - # " ! - Installation and electric works only by skilled and qualified personnel and in accordance to health and…
-
• Use self-locking screws only
• for fans with volumetric flow measuring equipment, make sure and adhere to the data sheet! • Electric wiring must be in accordance with local technical specifications and ordinances of the motor manufacturer. − Take care when fitting the cable into the terminal box that it is properly sealed and…
-
− Install protection guard / finger protection ( accessories) or give no access to
impeller. • ( ) , !* 2-! * ! , * ! Z1 ( (→ ) Z2 ( ) ) • Check direction of rotation as per direction arrow on the casing by short turning on. with 3-phase-motor - to change direction of rotation transpose two of the phases! with 1-phase-motor - to change direction of rotation transpose the position…
-
# & #. % # ( & '( % " ! ' 4, & ) ) (, " ( (, ) )! → ( " #! Only commence operation when fan is installed in accordance with ordinances ! If the fan is started under free blow conditions, i.e. prior to connecting to duct system, the current consumption may exceed the rated current (forbidden area of…
-
% # # − ! : − − % . $ ' % & & % 07 $ . : 710 # &. DIN 51825 3-6 # # ISO VG 68 / DIN 51519) . # ) ) &. " . $ ' % & &. . % & & 900 min-1 40000 $ )$ , 1400 min-1 $ )$ 2800 min-1 15000 30000 $ )$ . $ )$ &. & # "& 5 . 6 $ # & $ ( & , '& & & " '( '( ( . ( ) !) Use only original spare parts tested and…
-
at 2800 min-1 15000 hours,
Independent of the working hours bearings should be changed every 5 years. Only use usual commercial cleaning material paying attention to the prescribed safety measures and do not use any abrasive tools (surface protection will be destroyed ! • 7 − ( − - ! ) ! " - ! * − • Clean fan - clean inlet…
-
operating period of between 0.5 and 4 hours under full load and thereafter in intervals of about 24 operating hours. - Unscrew the protective cover of the belt - Inspect the drive belt as shown in figure 1 Κ if necessary, retighten the drive belt: 1. loosen the clamping screws on the side of the…
-
,$ & # & $ ( " ' ) &. &, . $ & $ " . " # - # # . & $) & &, & 1°. % # &- . . If the drive belt is not properly tightened, the result will be an inadequate transmission of power and a premature failure of the drive belt. A too high pretension will additionally be the cause of bearing damages. When…
-
/ REPAIR / 0 : & − & '$ − & "& # − ) # # . ! # % '$ ! Before any repairs are undertaken please: • Stop fan in accordance to regulations and disconnect all poles from mains supply. • Wait until impeller is stationary! • Make sure that a restart is not possible! # & ( % # $ . Only use original spare…
-
- - - remove the protective cover of the belt loosen the tension of the belt drive remove the drive belt on the side opposite of the drive, loosen the clamping screws of the ball bearings loosen the inlet cone mounting screws on the drive side remove the impeller together with the shaft from the…
-
! ( “" ( “" “) “) • Replacing the motor - disconnect the wiring of the motor - remove the protective cover of the belt - loosen the clamping screws on the motor carriage - release the tension of the belt drive - remove the pulley from the motor shaft (for this, loosen the Allen screws on the pulley…
-
' , & & 8 / Service, Address of Producer * „Rosenberg“ . , , : Rosenberg-products are subject to steady quality controls and are in accordance with valid regulations. In case you have any questions with regard to our products please contact either your constructor of your air handling unit or…
Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.