Инструкция на Высокотемпературные центробежные вентиляторы Systemair серии AXZENT/ AXZENT EC

Текст инструкции

1. Стр. 1 AxZent — Thermo centrifugal fan

   Installation and Operating Instructions Document in original language | · 004 GB

2. Стр. 2 © Copyright Systemair AB

   All rights reserved E&OE Systemair AB reserves the rights to alter their products without notice. This also applies to products already ordered, as long as it does not affect the previously agreed specifications. | 004

3. Стр. 5 General information |

   1 General information 1.1 Notice symbols Danger Caution Direct hazard Failure to comply with this warning will lead directly to death or to serious injury. Hazard with a low risk Failure to comply with this warning may lead to moderate injuries. Warning Important Potential hazard Failure to comply…

4. Стр. 6

   | Warranty Table 1 Qualifications Activities Qualifications Storage, operation, transport, cleaning, disposal Trained personnel (see following note) Electrical connection, commissioning, electrical disconnection Electrical expert or matching qualification Installation, disassembly Fitter or matching…

5. Стр. 7 Description |

   Unpacking When opening the transport packaging, there is a risk of damage from sharp edges, nails, staples, splinters etc. ♦ Unpack the fan carefully. ♦ Check the fan for obvious transport damage. ♦ Only remove the packaging shortly before assembly. Transport Safety information Warning: Electrical…

6. Стр. 8 таблицы и схемы — в просмотре

7. Стр. 9

   Name plate and type key | 6 Name plate and type key Type designation 5 Enclosure class/fan impeller speed/weight 2 Voltage/current/frequency 6 Insulation class 3 Input power 7 Article number/production number/manufacturing date 4 Max. temperature of transported air 8 Certifications Table 4 Type key…

8. Стр. 10

   | Accessories 7 Accessories Note: For details of the accessories, please check our online catalog or contact Systemair. Table 5 Accessories 1 SG Protection guard 7 AxZent Fan 2 ESD-F Inlet cone 8 LRK Air operated damper 3 RSA Silencer 9 GFL Counter flange 4 EVH Flexible connection 10 MFA Mounting…

9. Стр. 11 Installation |

   Important Damage to the bearings or other parts of the fan can occur. ♦ Do not place a duct bend directly before or after the fan! ♦ Ensure a smooth and constant air flow to the device. Important Damage to the bearings or other parts of the fan can occur. ♦ Do not place a duct bend directly before…

10. Стр. 12

    | Installation 1 Motor 2 Motor shaft 3 Sleeve (not available at every fan) 4 Shaft extension (not available at every fan) 2 5 Hexagon socket screw 4 6 Impeller 5 7 Steel hub 8 Aluminium hub The hub is shown without impeller due to better lucidity. Disassembly 1. Aluminium hub 1. Steel hub 2. 3. 4.…

11. Стр. 13 Electrical connection |

    5. Steel hub 6. Steel hub Tighten the two screws evenly with the tightening torque according to table 6. Tighten the screws slightly Table 6 Tightening torques for various types of bush Type of bush 1008 1108 1210 1215 1310 1610 1615 2012 2517 3020 Tightening torque [Nm] 5.7 5.7 Electrical…

12. Стр. 14

    | Electrical connection Wire- colours of motors with carried out cables: +10V = red GND = blue 0..10V/PWM = yellow Controll via 0–10V signal MTP 10 S-5EC/FRQ MTP 20 S-5EC/FRQ 10V GND A MTV—1/10 EC-Basic EC-Vent EC-Vent IN/RPM optional TACH +10V IN/10V OUT/PWM PWM 0...10V/PWM GND GND Controll via…

13. Стр. 15 Commissioning |

    9.3 Variable-speed fans Warning Resonant frequencies may result in increased vibration in certain speed ranges. These vibrations may destroy components. ♦ Only operate the fan outside these speed ranges. ♦ Pass through these speed ranges so quickly that any vibration cannot exceed the admissible…

14. Стр. 16

    | Troubleshooting/maintenance/repair 12 Troubleshooting/maintenance/repair Safety information ♦ Observe 2 Important safety information, page 1 12.1 Troubleshooting Table 7 Troubleshooting Fan does not run smoothly Air output of fan too low Grinding sounds when starting or operating the fan Thermal…

15. Стр. 17 Troubleshooting/maintenance/repair |

    Troubleshooting cont'd Motor does not rotate Electronics/motor overheated Faulty supply voltage Check the supply voltage, re-establish the voltage supply. Faulty connection Allow the motor to cool down, find and resolve the cause of the fault. Temperature monitor has responded. Allow the motor to…

16. Стр. 18

    | Cleaning Activities cont'd Check the connection clamps and screwed cable connections for damage/defects, and check that they are firmly seated. Check the flexible connectors for damage. X X See normal operating conditions See normal operating conditions Spare parts ♦ Use original spare parts from…

17. Стр. 19

    16 EU Declaration of conformity The manufacturer: Systemair GmbH Seehöfer Straße 45 97944 Boxberg Germany Product designation: Thermo fans Type designation: AxZent; KBR; MUB-K; MUB/T; MUB/T-S; DVN; DVNI Since year of manufacture: 2018 The manufacturer declares that the above mentioned products in…

18. Стр. 20

    | Commissioning Report 17 Commissioning Report Warranty claims can only be made if commissioning work is carried out correctly and written evidence thereof is provided. Fan Description: Article no.: Manufacturing order no.: Installer Company: Contact person: Company address: Tel. no.: Email…

19. Стр. 21 Commissioning Report |

    Current L1 [A]*: Fan impeller speed [rpm]: Current L2 [A]: Air volume [m3/s]: Current L3 [A]: Differential pressure [Pa]*: *For single-phase fans, fill in line “Current L1 [A]” *Δ- Pressure between suction-side and discharge of the fan If an air flow measurement is not possible, this value can be…

20. Стр. 22 Tel.: +49 (0)7930/9272-0

    Fax: +49 (0)7930/9273-92 info@systemair.de www.systemair.de AxZent — Thermo centrifugal fan · Installation and Operating Instructions · · en_GB · 2020-02-11 · 004 Systemair GmbH Seehöfer Str. 45 97944 Boxberg Germany

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.