Инструкция на Кондиционеры серии SAP бренда Sanyo

TECHNICAL & SERVICE MANUAL

SAP – K71GJHA + SAP – C71GHA SAP – K91GJHA + SAP – C91GHA SAP – K121GJHA + SAP – C121GHA FILE NO. SPLIT SYSTEM AIR CONDITIONER Indoor Model No. Product Code No. SAP – K71GJHA–S SAP – K91GJHA–S SAP – K121GJHA–S Destination Outdoor Model No. Product Code No. SAP – C71GHA–S General (50Hz) SAP…

When Transporting

Important! Please Read Before Starting Be careful when picking up and moving the indoor and outdoor units. Get a partner to help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin aluminum fins on the air conditioner can cut your fingers. This air conditioning…

1. OPERATING RANGE

2. SPECIFICATIONS

2-1. Unit Specifications Indoor Unit Outdoor Unit SAP – K71GJHA SAP – C71GHA Power Source 220–240V Single phase 50Hz Voltage rating 220/230/240 V Performance Cooling Capacity kW BTU/h Air circulation (High) Moisture removal (High) m3/h Liters/h 2.05 7,000 / / Electrical Rating 2.05 7,000 400 0.56…

SAP – K91GJHA

SAP – C91GHA Power Source 220–240V Single phase 50Hz Voltage rating 220/230/240 V Performance Cooling Capacity kW BTU/h Air circulation (High) Moisture removal (High) m3/h Liters/h 2.55 8,700 / / Electrical Rating 2.55 8,700 430 0.85 Heating / / 2.55 8,700 3.20 / 3.25 / 3.30 10,900 / 11,100 / 11,300…

SAP – K121GJHA

SAP – C121GHA Power Source 220–240V Single phase 50Hz Voltage rating 220/230/240 V Performance Capacity kW BTU/h Air circulation (High) Moisture removal (High) m3/h Liters/h Cooling Heating 3.20 / 3.20 / 3.25 10,900 / 10,900 / 11,100 470 1.45 3.70 / 3.75 / 3.80 12,600 / 12,800 / 13,000 460 — Cooling…

2-2. Major Component Specifications

2-2-1. Indoor Unit Indoor Unit SAP – K71GJHA Controller PCB Part No. Controls Control circuit fuse POW-K71GJHA Microprocessor 250 V 3.15 A Remote Control Unit RCS-2HS2E Fan & Fan Motor Type Q'ty Dia. and length Fan motor model Q'ty No. of poles 50Hz rpm (High) Nominal output Coil resistance (Ambient…

SAP – K91GJHA

Controller PCB Part No. Controls Control circuit fuse POW-K91GJHA Microprocessor 250 V 3.15 A Remote Control Unit RCS-2HS2E Fan & Fan Motor Type Q'ty Dia. and length Fan motor model Q'ty No. of poles 50Hz rpm (High) Nominal output Coil resistance (Ambient temp. 20°C) Safety devices Type Operating…

SAP – K121GJHA

Controller PCB Part No. Controls Control circuit fuse POW-K121GJHA Microprocessor 250 V 3.15 A Remote Control Unit RCS-2HS2E Fan & Fan Motor Type Q'ty Dia. and length Fan motor model Q'ty No. of poles 50Hz rpm (High) Nominal output Coil resistance (Ambient temp. 20°C) Safety devices Type Operating…

2-2-2. Outdoor Unit

Outdoor Unit SAP – C71GHA Controller PCB POW-C96GH-S Compressor Type Compressor model Nominal output Compressor oil Amount Coil resistance (Ambient temp. 25°C) Safety devices Rotary (Hermetic) C-1R71H5V 80688845-S 700 4GSD-T or SAY-56T 320 C–R : 4.57 C–S : 6.90 External(OLR A) External(OLR T)…

SAP – C91GHA

Controller PCB POW-C96GH-S Compressor Type Compressor model Nominal output Compressor oil Amount Coil resistance (Ambient temp. 25°C) Safety devices Rotary (Hermetic) C-R92H5W 80692945-S 900 4GSD-T or SAY-56T 550 C–R : 3.07 C–S : 7.97 External(OLR A) External(OLR T) MRA99057-9201 CS-7C115 145±5…

Controller PCB

POW-C186GH Compressor Type Compressor model Nominal output Compressor oil Amount Coil resistance (Ambient temp. 25°C) Safety devices W cc Ω Type Overload relay Operating temp. Open °C Close °C Operating amp.(Ambient temp. 25°C) Run capacitor µF VAC Crank case heater Rotary (Hermetic) C-R112H5X…

2-3. Other Component Specifications

Indoor Unit SAP – K71GJHA SAP – K91GJHA SAP – K121GJHA Transformer (TR) Rating Coil resistance ATR-J105 Primary AC 230V, 50 / 60 Hz Secondary 19V, 0.526A Capacity 10VA Ω (at 21°C) Primary (WHT – WHT): 205 ± 10% Secondary (BRN – BRN): 2.0 ± 10% Thermal cut-off temp. 150°C Thermistor (Coil sensor)…

3. DIMENSIONAL DATA

Indoor Unit SAP – K71GJHA SAP – K91GJHA SAP – K121GJHA (3) 41.0 41.0 172 Remote control unit 58.5 Center of tubing hole (2 places) Drain hose ø18 Narrow tube ø6.35 (1/4") Wide tube ø9.52 (3/8") Wide tube ø12.7 (1/2") 12 K71, K91 K121 Unit : mm

SAP – C71GHA

SAP – C91GHA 2 – ø12 holes (C91 only) Air intake Wide tube service valve ø9.52 (3/8") Air discharge Narrow tube service valve ø6.35 (1/4") Unit : mm 13

2 – ø12 holes

Air intake Wide tube service valve ø12.7 (1/2") Air discharge Narrow tube service valve ø6.35 (1/4") Outdoor Unit 150 Unit : mm 14

4. REFRIGERANT FLOW DIAGRAM

Outdoor Unit Indoor unit Outdoor unit Accumulator Wide tube service valve Heat exchanger Narrow tube Narrow tube service valve and cooling) (for heating) Cooling cycle Strainer O.D. ø6.35 mm (1/4") Indoor Unit Capillary tubes Capillary tube (both for heating Check valve Heating cycle SAP – K121GJHA…

5. PERFORMANCE DATA

5-1. Performance charts Indoor Unit Outdoor Unit SAP – K71GJHA SAP – C71GHA ■ Cooling Characteristics ■ Heating Characteristics 9 Indoor inlet air D.B. temp. (°C) 8 Operating current (A) Operating current (A) –5 50 MPa (kgf/cm2G) Indoor inlet air D.B. temp. (°C) 1.38 (13) 1.28 (12) 1.18 (11) 1.08…

SAP – K91GJHA

SAP – C91GHA ■ Cooling Characteristics ■ Heating Characteristics 9 Indoor inlet air D.B. temp. (°C) 8 Operating current (A) Operating current (A) –5 50 MPa (kgf/cm2G) Indoor inlet air D.B. temp. (°C) 1.38 (13) 1.28 (12) 1.18 (11) 1.08 (10) 0.98 ( 9 ) 0.89 ( 8 ) 0.79 ( 7 ) 0.69 ( 6 ) 0.59 ( 5 ) 0.49…

SAP – K121GJHA

SAP – C121GHA ■ Cooling Characteristics ■ Heating Characteristics 11 Indoor inlet air D.B. temp. (°C) Operating current (A) Operating current (A) 11 Outdoor fan speed Low High –5 50 MPa (kgf/cm2G) Indoor inlet air D.B. temp. (°C) 1.38 (13) 1.28 (12) 1.18 (11) Outdoor fan speed 1.08 (10) Low High…

5-2. Air Throw Distance Chart

Indoor Unit SAP – K71GJHA Cooling Room air temp. : Fan speed : 27°C High Horizontal distance (m) Axis air verocity (m/s) Vertical distance (m) : Flap angle 0° , : Flap angle 30°, : Axis air velocity 0° : Axis air velocity 30° Heating Room air temp. : Fan speed : 20°C High Horizontal distance (m)…

SAP – K91GJHA

Cooling Room air temp. : Fan speed : 27°C High Horizontal distance (m) Axis air verocity (m/s) Vertical distance (m) : Flap angle 0° , : Flap angle 30°, : Axis air velocity 0° : Axis air velocity 30° Heating Room air temp. : Fan speed : 20°C High Horizontal distance (m) Axis air verocity (m/s)…

SAP – K121GJHA

Cooling Room air temp. : Fan speed : 27°C High Horizontal distance (m) Axis air verocity (m/s) Vertical distance (m) : Flap angle 0° , : Flap angle 30°, : Axis air velocity 0° : Axis air velocity 30° Heating Room air temp. : Fan speed : 20°C High Horizontal distance (m) Axis air verocity (m/s)…

5-3. Cooling Capacity

Indoor Unit Outdoor Unit SAP – K71GJHA SAP – C71GHA 240V Single Phase 50Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °C W.B. D.B. TC CM 21 SHC 15 23 SHC 25 SHC 27 SHC 29 SHC 31 SHC TC CM 21 SHC 17 23 SHC 25 SHC 27 SHC 29 SHC 31 SHC TC CM 21 SHC 19 23 SHC 25 SHC 27 SHC 29 SHC 31 SHC TC CM…

SAP – K91GJHA

SAP – C91GHA 240V Single Phase 50Hz RATING CAPACITY AIR FLOW RATE EVAPORATOR ENT. TEMP. °C W.B. D.B. TC CM 21 SHC 15 23 SHC 25 SHC 27 SHC 29 SHC 31 SHC TC CM 21 SHC 17 23 SHC 25 SHC 27 SHC 29 SHC 31 SHC TC CM 21 SHC 19 23 SHC 25 SHC 27 SHC 29 SHC 31 SHC TC CM 23 SHC 21 25 SHC 27 SHC 29 SHC 31 SHC TC…

SAP – K121GJHA

SAP – C121GHA 240V Single Phase 50Hz RATING CAPACITY 3.25 kW AIR FLOW RATE 470 m3/h EVAPORATOR CONDENSER ENT. TEMP. °C OUTDOOR AMBIENT TEMP. °C W.B. D.B. TC 2.99 2.85 2.67 2.46 CM 1.04 1.11 1.22 1.35 21 SHC 1.98 1.91 1.82 1.71 15 23 SHC 2.21 2.13 2.04 1.94 25 SHC 2.44 2.36 2.27 2.16 27 SHC 2.66 2.58…

Heating capacity ratio (%)

5-4. Heating Capacity –8 –5 Outdoor temperature (°C D.B.) NOTE 1) … Point of Rating condition Black dot in the chart indicate the following rating condition. Indoor : 20°C D.B. Outdoor : 7°C D.B. / 6°C W.B. 2) Above characteristics indicate instantaneous operation, which does not take into account…

6. ELECTRICAL DATA

6-1. Electrical Characteristics Indoor Unit Outdoor Unit SAP – K71GJHA SAP – C71GHA COOLING Indoor Unit Outdoor Unit Fan Motor Fan Motor Performance at Rating Conditions Complete Unit Compressor 220 – 240V Single phase 50Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input A…

SAP – K91GJHA

SAP – C91GHA COOLING Indoor Unit Outdoor Unit Fan Motor Fan Motor Performance at Rating Conditions Complete Unit Compressor 220 – 240V Single phase 50Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input A 0.17 / 0.18 0.24 / 0.25 3.89 / 3.87 4.3 / kW 0.034 / 0.040 4.3 0.052 /…

SAP – K121GJHA

SAP – C121GHA COOLING Indoor Unit Outdoor Unit Fan Motor Fan Motor Performance at Rating Conditions Complete Unit Compressor 220 – 240V Single phase 50Hz Running Amps. Power Input Full Load Conditions Running Amps. Power Input A 0.17 / 0.18 0.24 / 0.25 5.39 / 5.47 5.8 / kW 0.034 / 0.040 5.9 0.052 /…

6-2. Electric Wiring Diagrams

Indoor Unit SAP – K71GJHA SAP – K91GJHA SAP – K121GJHA WARNING 29 To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical parts.

SAP – C71GHA

SAP – C91GHA WARNING 30 To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical parts.

WARNING

31 To avoid electrical shock hazard, be sure to disconnect power before checking, servicing and/or cleaning any electrical parts.

7. INSTALLATION INSTRUCTIONS 7-1. Installation Site Selection ● Wall-mounted Type Indoor Unit WARNING To prevent abnormal heat generation and the possibility of fire, don’t place obstacles, enclosures and grills in front of or surrounding the air conditioner in a way that may block air flow. AVOID…

AVOID

● heat sources, exhaust fans, etc. (Fig. 3) NO ● damp, humid or uneven locations. Exhaust fan Hot air Heat source DO: ● choose a place as cool as possible. Outdoor unit ● choose a place that is well ventilated. ● allow enough room around the unit for air intake/exhaust and possible maintenance.…

7-2. Remote Control Unit Installation

Position The remote control unit can be operated from either a non-fixed position or a wall-mounted position. To ensure that the air conditioner operates correctly, do not install the remote control unit in the following places: ● In direct sunlight ● Behind a curtain or other place where it is…

7-3. Recommended Wire Length and Diameter

Regulations on wiring diameter differ from locality to locality. For field wiring requirements, please refer to your local electrical codes. Carefully observe these regulations when carrying out the installation. NOTE Refer to the WIRING SYSTEM DIAGRAM for the meaning of "A" and "B" in Table 2.…

8. FUNCTION

8-1. Room Temperature Control ■ Cooling ● Room temperature control is obtained by cycling the compressor ON and OFF under control of the room temperature sensor in the remote control unit. ● The room temperature (and other information) is transmitted every 3 minutes by the remote control unit to the…

■ Heating

● Room temperature control is obtained by cycling the compressor ON and OFF under control of the room temperature sensor in the remote control unit. ● The room temperature (and other information) is transmitted every 3 minutes by the remote control unit to the controller in the indoor unit. Signal…

8-2. Dry Operation (Dehumidification)

● Dry operation uses the ability of the cooling cycle to remove moisture from the air, but by running at low level to dehumidify without greatly reducing the room temperature. The air conditioner repeats the cycle of turning ON and OFF automatically as shown in the chart below according to the room…

8-4. Freeze Prevention (Cooling)

● This function prevents freezing of the indoor heat exchange coil. ● When the compressor has been running for 10 minutes or more and the temperature of the indoor heat exchange coil falls below –1°C, the control circuit stops the compressor for at least 6 minutes. The compressor does not start…

8-5. Overload Prevention (Heating)

● This function prevents overheating of the indoor heat exchange coil. ● When the temperature of the indoor heat exchange coil rises above 54°C, and if the indoor fan is L (low speed), then the fan speed changes from L (low speed) to M (medium speed). ● When the temperature of the indoor heat…

8-6. Cold Draft Prevention (Heating)

● This function controls indoor fan speed so a strong draft of cold air will not blow out before the indoor heat exchange coil have sufficiently warmed up. ● STANDBY lamp on front of the indoor unit lights up when this function is working. ● when 10 minutes has elapsed,the fan speed is automatically…

8-7. Defrosting Operation (Heating)

■ Defrosting Flowchart Compressor ON Release of overload prevention (Outdoor fan operates.) Overload prevention works. Does outdoor fan stop? YES NO A B Outdoor fan is either operated or stopped for more than 10 minutes. NO C Indoor heat exchanger coil temperature drops 0.8°C per 6 minutes and it…

■ Defrosting Mode Timing Chart

Release of defrosting Start of defrosting 32 seconds Compressor ON Outdoor fan ON OFF 11 minutes ON 32 seconds ON OFF ON 2 seconds Solenoid coil (4–way valve) Indoor fan ON OFF 2 seconds OFF ON ON Set speed Standby lamp OFF Set speed ON ON OFF Indoor heat exch. coil ✻1 temp. 34 °C ✻1 Release of cold…

9. TROUBLESHOOTING

9-1. Check before and after troubleshooting WARNING Hazardous voltage can cause ELECTRIC SHOCK or DEATH. Disconnect power or turn off circuit breaker before you start checking or servicing. 9-1-1. Check power supply wiring. ● Check that power supply wires are correctly connected to terminals No.8…

9-2. Air conditioner does not operate

9-2-1. Circuit breaker trips (or fuse blows). A. When the circuit breaker is set to ON, it is tripped soon. (Resetting is not possible.) ● There is a possibility of ground fault. ● Check insulation resistance. If resistance value is 2MΩ or less, insulation is defective (“NO”). 2 Indoor unit 1…

B. Circuit breaker trips in several minutes after turning the air conditioner on

● There is a possibility of short circuit. • Check capacity of circuit breaker. Replace with suitable one (larger capacity). NO Capacity of circuit breaker is suitable. In case of Heating operation : • Measure resistance of 4-way valve's winding. • Measure resistance of outdoor fan motor winding. •…

C. Check remote control unit

• Try to run with another remote control unit. OK First remote control unit is defective. • Check for residue buildup on transmitter of remote control unit. Clean transmitter. • Check for residue buildup on remote control receiver on front of indoor unit. Clean receiver. D. Check fuse on the indoor…

9-2-3. Only outdoor unit does not run

A. Check setting temperature. Is room temperature too low ? Is room temperature too high ? NO NO Try to lower setting temperature by temperature setting button ( button). Try to raise setting temperature by temperature setting button ( button). Outdoor unit still does not run. Outdoor unit still…

9-3. Some part of air conditioner does not operate

9-3-1. Only indoor fan does not run. • Check fan rotation. Turn fan gently once or twice by hand. Fan cannot be turned. • Measure resistance of indoor fan motor winding. • Check fan casing foreign matter on inside. Remove foreign matter or repair. Fan motor burnout or foreign matter in bearings.…

9-3-4. Only outdoor fan does not run

Fan cannot be turned. • Check fan rotation. Turn fan gently once or twice by hand. • Check fan casing foreign matter on inside. Remove foreign matter or repair. Fan motor burnout or foreign matter in bearings. Repair or replace. • Measure resistance of outdoor fan motor winding. OK • Check fan motor…

9-4. Air conditioner operates, but abnormalities are observed

9-4-1. Operation does not switch from HEAT to COOL (or COOL to HEAT). • Remote control unit may be defective. Receiver in switch Ass'y may be defective. • Measure resistance of 4–way valve's winding. COOL ➞ HEAT • Check voltage between terminals No. 4(+) and No. 6 at terminal plate. (DC 24V) OK…

9-4-2. Poor cooling or heating

• Check position of remote control unit. • Cool air from air conditioner reaches position directly. YES Change position of remote control unit. • Wide and narrow tubes between indoor unit and outdoor unit are insulated. NO Insulate both wide and narrow tubes separately and then tape together. YES •…

9-5-1. Indoor coil temp. thermistor (TH1) is defective. • Operation lamp on front side of indoor unit is flashing on and off. (*) YES • Thermistor (TH1 ) is defective. (That is, sensor is SHORT.) YES • Replace thermistor. NOTE Alarm Signal (*) Operation lamp on the front side of the indoor unit will…

10. CHECKING ELECTRICAL COMPONENTS

10-1. Measurement of Insulation Resistance Ground wire Clip ● The insulation is in good condition if the resistance exceeds 2MΩ. Probe 10-1-1. Power Supply Wires Insulation tester Clamp the ground wire of the power supply wires with the lead clip of the insulation resistance tester and measure the…

10-2. Checking Continuity of Fuse

on PCB Ass'y Fuse ● Remove the PCB Ass’y from the electrical component box. Then pull out the fuse from the PCB Ass’y. (Fig. 5) PCB Ass’y ● Check for continuity using a multimeter as shown in Fig. 6. Fig. 5 10-3. Checking Motor Capacitor Remove the lead wires from the capacitor terminals, and then…

11. MAINTENANCE

11-1. Changing Address of Remote Control Unit in Indoor Unit If you are installing more than 1 indoor unit (up to 2) in the same room, it is necessary for you to assign each unit its own address, so each can be operated by its own separate remote control unit. You assign the addresses by matching…

APPENDIX INSTRUCTION MANUAL

SAP – K71GJHA + SAP – C71GHA SAP – K91GJHA + SAP – C91GHA SAP – K121GJHA + SAP – C121GHA 57

Features

This air conditioner is equipped with cooling, heating, and drying functions. Details on these functions are provided below; refer to these descriptions when using the air conditioner. • Compact Size This model is smaller than its predecessors and yet offers the same capabilities. • Microprocessor…

Installation Location

We recommend that this air conditioner be installed properly by qualified installation technicians in accordance with the Installation Instructions provided with the unit. Before installation, check that the voltage of the electric supply in your home or office is the same as the voltage shown on…

Names of Parts

Air intakes INDOOR UNIT Air outlet Remote control unit Drain hose Refrigerant tubes OUTDOOR UNIT Air outlet NOTE This illustration is based on the external appearance of a standard model. Consequently, the shape may differ from that of the air conditioner you have selected. This air conditioner…

Unit Display and Operation Selector

Operation selector INDOOR UNIT IMPORTANT Avoid using radio equipment such as mobile phone near (within 1 m of) the indoor unit. Some radio equipment may cause the unit to malfunction. If the trouble occurs, disconnect power and restart the air conditioner after a few minutes. Remote control receiver…

Remote Control Unit (Display)

Displayed when setting temperature Displayed when transmitting data Displayed when temperature is shown Displayed when the temperature setting is at the upper or lower allowable limit Displayed when setting timer Symbols (1) Operation mode AUTO (3) Set temperature 16–30°C When set to 28°C C COOL (4)…

Remote Control Unit

Transmitter Display (Cover closed) ON/OFF operation button 1 HR. TIMER button Temperature setting buttons (TEMP.) NIGHT SETBACK button MODE selector button FAN SPEED selector button FLAP button TIMER SET button (which advances the time displayed) TIMER ON button ADDRESS switch TIMER OFF button ACL…

Remote Control Unit (continued)

TIMER ON button : The air conditioner starts at the set time. TIMER OFF button : The air conditioner stops at the set time. TIMER SET button This button is used to set the time at which you wish the air conditioner to go on or off. MODE selector button (AUTO) Use this button to select AUTO, HEAT…

Using the Remote Control Unit

How to Install Batteries 1. Slide the cover in the direction indicated by the arrow and remove it. 2. Install two AAA alkaline batteries. Make sure the batteries point in the direction marked in the battery compartment. 3. Use a thin object such as the tip of a pen to press the ACL button. ACL…

Using the Remote Control Unit (continued)

Mounting the Remote Control Unit Truss-head tapping screws 4 x 16 mm (supplied) Press Remote control unit holder When attaching to wall Hook 1) Confirm the indoor unit beeps when the ON/OFF button is pressed at the wall location where the remote control unit is to be attached, then attach the holder…

Operation with the Remote

Control Unit 1. Automatic Operation STEP 2 STEP 1 NOTE Check that the circuit breaker on the power panel is turned on and that the operation selector of the indoor unit is in the ON position. mode is selected and the unit is preset by following the steps Once below, you can have the air conditioner…

2. Manual Operation

STEP 2 STEP 3 STEP 1 STEP 5 NOTE STEP 4 Check that the circuit breaker on the power panel is turned on and that the operation selector of the indoor unit is in the ON position. If the automatic operation settings of the unit do not meet your needs, press the setting buttons as described below and…

NOTE

• This appliance has a built-in 3-minute time delay circuit to ensure reliable operation. When the operation button is pressed, the compressor will start running within three minutes. In the event of power failure, the unit will stop. When the power is restored, the unit will restart automatically…

4. Night Setback Mode

Night Setback Mode is used for saving energy. Press the NIGHT SETBACK button while operation. mark appears in the display. The To release the night setback function, press the NIGHT SETBACK button again. A. In Cooling and DRY Mode: ( and ) When the night setback mode is selected, the air conditioner…

( ) When the night setback mode is selected, the air conditioner automatically lowers the temperature setting 2°C when 30 minutes have passed after the selection was made, and then another 2°C after another 30 minutes have passed, regardless of the indoor temperature when night setback was selected.…

Special Remarks

‘‘DRY’’ ( ) Operation How it works? • • • Heating ( Once the room temperature reaches the level that was set, the unit repeats the cycle of turning on and off automatically. During DRY operation, the fan speed is automatically set to LOW or VERY LOW; the fan speed then switches back and forth…

Using the 12-Hour ON and OFF

Timer 1. TIMER ON mode (Example) After the length of time set for TIMER ON elapses, the unit begins operating. The display depicted at left indicates that the air conditioner will begin operating in three hours. Setting procedure: STEP 1 STEP 2 STEP 3 • • Press the MODE button and set the desired…

Using the 12-Hour ON and OFF Timer (continued)

3. ON/OFF Program Timer A combination of the TIMER ON and TIMER OFF modes, this function allows you to specify the time that the unit turns on and the time when it turns off. (Example) The unit will turn on three hours from now, and turn off five hours from now. Timer setting Stop Operate 3 hours 2…

Using the 1-Hour OFF Timer

1. 1-Hour OFF Timer This function causes the unit to operate for one hour and then stop, regardless of whether the unit is on or off when this button is pressed. The 1HR. indicator in the display indicates that this function is operating. Setting procedure: Regardless of whether the unit is…

Adjusting the Airflow Direction

1. Horizontal The horizontal airflow can be adjusted by moving the vertical vanes with your hands to the left or right. CAUTION When the humidity is high, the vertical vanes should be in the front position during the cooling or dehumidifying operation. If the vertical vanes are positioned all of the…

Operation without the Remote

Control Unit INDOOR UNIT If you have lost the remote control unit or it is not working properly, follow the steps below. 1. When the air conditioner is not running If you want to turn on the air conditioner, switch the operation selector to the OFF position, and then to the ON position. NOTE…

Care and Cleaning (continued)

Anti-Mold Filter How to remove the anti-mold filter The anti-mold filter behind the air intake grille should be checked and cleaned at least once every two weeks. 1. Grasp both ends of the air intake grille and pull it out and up. Air intake grille 2. Push the anti-mold filter up slightly, and then…

Care and Cleaning (continued)

Air Cleaning Filter (not provided) NOTE The air cleaning filter removes dust and dirt from the air, and reduces odors and smoke from tobacco. The air cleaning filter is not provided with the air conditioner and must be purchased separately. The first time that you buy the air cleaning filter, it is…

Troubleshooting

If your air conditioner does not work properly, first check the following points before requesting service. If it still does not work properly, contact your dealer or service center. Trouble Air conditioner does not run at all. Possible Cause 1. Power failure. 2. Leakage breaker tripped. 3. Line…

SANYO Electric Co.,Ltd

Osaka, Japan SM700457 Printed in Japan 10/00/200

Инструкция на Кондиционеры серии SAP

Текст инструкции

Новое в каталогах

Новое в инструкциях