Инструкция на Масла для винтовых компрессоров GEA (типоразмеры C…XH)
Перечень допущенных смазочных масел для винтовых компрессоров GEA типоразмеров C…XH в холодильных применениях, при компрессии газов и в тепловых насосах; рекомендации по выбору холодильного масла. Техническая информация C_505511_19. Документ на английском языке.
Загружаем документ…
Текст инструкции
-
GEA Screw compressor
Frame size C XH Technical Information (Translation from the original language) C_505511_19
-
TABLE OF CONTENTS
1 LUBRICATING OILS FOR SCREW COMPRESSORS 5 1.1 1.2 1.3 Oil Selection list for Refrigeration Applications and Gas Compression Oil Selection list for Heat pump Applications HINTS FOR SELECTION OF REFRIGERATION OIL C_505511_19 16.06.2021 3
-
LUBRICATING OILS FOR SCREW COMPRESSORS 1.1 Oil Selection list for Refrigeration Applications and Gas Compression For screw compressors of GEA Refrigeration Germany GmbH, the oils specified in the tables are approved. The selection of the oils depends on the chemical properties of the oil, the…
-
Table 1: Lubricating oils for R717 (ammonia)
( primarily recommended especially if minimum oil carry-over from the oil separator is important) Viscosity at 40 deg. C in cSt (Page 22) Flash point in deg. C (Page 22) Pour point in deg. C (Page 22) Manufacturer Type of oil Basis (Page 18) TEXACO Capella Premium M*-PAO 67 262 -42 Paramo Mogul…
-
Table 2: Lubricating oils for dry evaporation applications (DX) with R717 (ammonia)
Manufacturer Mobil Type of oil Zerice S32 Basis (Page 18) Viscosity at 40 deg. C in cSt (Page 22) Flash point in deg. C (Page 22) Pour point in deg. C (Page 22) Remark AB 32 154 -33 Please contact manufacturer NSF grade 1) 1) Application area in food-processing industry according to NSF…
-
Table 3: Lubricating oils for R717 (ammonia) and R22
Basis (Page 18) Viscosity at 40 deg. C in cSt (Page 22) Flash point in deg. C (Page 22) Pour point in deg. C (Page 22) Remark Aircol 299 M 56 180 -34 for R22 only Aircol AMX 68 M 28 260 -30 for R717 only Aircol 2294 PAO 69 233 -60 for R717 only Zerice S32 AB 32 154 -33 Manufacturer Castrol MOBIL…
-
Manufacturer Castrol Type of oil Aircol SW 68 Basis (Page 18) Fuchs MOBIL TOTAL Pour point in deg. C (Page 22) 68 245 -39 250 -27 64 266 -43 125 262 -33 Solest -27 Reniso Triton SE -48 Reniso Triton SEZ -39 82 251 -39 Reniso Triton SEZ -30 Reniso Triton SE -27 220 240 -38 66 230 -42 94 230 -42 68…
-
Notice
Advice for the first filling ► When using high-viscosity oils with high refrigerant solubility after initial fill of the plant a sufficient mixture from refrigerant and oil has to be provided before start-up the screw compressor. 10 C_505511_19 16.06.2021
-
Table 5: Lubricating oils for natural gas and hydrocarbon compounds
Basis (Page 18) Viscosity at 40 deg. C in cSt (Page 22) Flash point in deg. C (Page 22) Pour point in deg. C (Page 22) M 68 234 -21 for natural gas compression CPI 1515-68 67 224 -43 CPI 1515-100 100 210 -48 For heavy hydrocarbons, where strong dilution or condensation will occur 68 218 -48 CPI…
-
Table 6: Lubricating oils for R744 (CO2)-application
Manufacturer CPI Fuchs Klüber Lubrication Mobil Type of oil CPI 4624-46F CPI 4624-68F Basis (Page 18) Viscosity at 40 deg. C in cSt (Page 22) Flash point in deg. C (Page 22) Pour point in deg. C (Page 22) 46 246 -60 H1 68 268 -51 H1 246 -42 complete miscible -30 attend to the miscibility gap E* 80…
-
Table 7: Use of O-ring elastomer in screw compressors depends on refrigerant and lubricant
Oil Refrigerant M M* M*PAO AB E PAO ABPAO PAG R717 (ammonia) CR*)/ HNBR CR*)/ HNBR CR*)/ HNBR CR - CR CR CR/ HNBR R22 CR - - CR CR - CR - R134a, R404A, R407C, R410A, R507, R23 - - - - HNBR - - - R290 (propane), R1270 (propylene) - - - - - HNBR - HNBR R744 (Carbon dioxide CO2) - - - - CR HNBR - CR *)…
-
Notice
Advice for trouble-free operation ► The specified range of viscosity of the lubricating oil upstream of the compressor has to be observed in any case. At the same time, it must be noted that refrigerant/oil combinations are possible in which, dependent on the pressure and temperature in the oil…
-
Oil Selection list for Heat pump Applications For screw compressors of GEA Refrigeration Germany GmbH, the oils specified in the tables are approved. The selection of the oils depends on the chemical properties of the oil, the refrigerants, the operating conditions of the plant and the required oil…
-
Notice
Recommended oil check intervals when using mineral oil ► Discharge temperature 95°C and oil temperature approx. 70°C: 1. first oil check after 500 operating hours 2. second oil check after 1000 operating hours 3. afterwards an oil check after every 1000 operating hours 4. After 5000 operating hours…
-
Notice
Advice for trouble-free operation ► The specified range of viscosity of the lubricating oil upstream of the compressor has to be observed in any case. At the same time, it must be noted that refrigerant/oil combinations are possible in which, dependent on the pressure and temperature in the oil…
-
HINTS FOR SELECTION OF REFRIGERATION OIL The characteristics of refrigerating machine oil influence the functionality of a refrigerator with oil flooded screw compressors, since this cannot be precluded despite the high-capacity oil separator and remnants of refrigerating machine oil can enter the…
-
The base oil versions mentioned will bring about differing oil carry-over rates as the flash points of the oils cited differ greatly from each other (lowest flash point of alkyl benzene at approx. 160 °C, highest flash point of polyalphaolefin considerably above 200 °C). Although the fluidity of the…
-
With relation to oils, the refrigerants feature the following properties
• Ammonia Ammonia is slightly soluble with lubricants. The mechanical mixture is very intense so that oil is always carried with the ammonia. Due to the low share of ammonia, the lubrication of the oil will not change and the miscibility of oil and refrigerant during the liquid phases is not…
-
5. Polyglycol oil
Polygylcol oils are soluble in ammonia and very hygroscopic. They are thus subject to the same handling conditions as ester oils. When selecting oils the drop in viscosity resulting from dissolving refrigerants in the oil needs to be taken into consideration. The flowablility of the oil in the…
-
PARAMETERS USED FOR OILS
Specific density The density difference between the coolant and oil may be important for the oil return. Care should be taken that alkyl benzine has a lower density than mineral oils and polyglycol and greater density than mineral oil. The methods for measuring density is described in DIN 51757.…
-
Aniline point
The aniline point indicates the temperature at which a homogeneous solution will clear when warmed with a constant volume share of a lubricant or lubrication material or oil and aniline when cooling and clouding occurs through separation upon cooling. The aniline point is the measurement of…
-
rm engineering for
р ии И, а better world We live our values. Excellence - Passion - Integrity - Responsibility - GEA-versity GEA Group is a global engineering company with multi-billion euro sales and operations in more than 50 countries. Founded in 1881, the company is one of the largest providers of innovative…
Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.