Инструкции на Клапаны и измерительные устройства Lindab

Текст инструкции

1. Стр. 1 Mounting instruction

   Dampers DRU, DSU, DTU, DTHU, DTH1U, DTH2U, DTBU DTBCU, DTFU, DTBLU, DSUSN, DSVUSN, DTPU, PSDRU, TDRU, TDSU TASU, TATU, TATBU, LKSR DAU, DA2EU, DAVU, CARU, CAR, MBU, MBFU FMU, FMDRU, FMDU, DIRU, DIRBU, DIRVU

2. Стр. 2 DRU, DSU, DTU, DTHU, DTH1U, DTH2U, DTBU,

   DTBCU, DTFU, DTBLU, DSUSN, DSVUSN, DTPU, PSDRU, TDRU, TDSU, TASU, TATU, TATBU Assembly In order to fulfil the requirements for air-tightness class D, the dampers must be installed as per ‘Assembly Instruction Lindab Safe’. For certain manual dampers, there is the option of adding a motor later on.…

3. Стр. 3 таблицы и схемы — в просмотре

4. Стр. 4 DRU, DSU, DTU, DTHU, DTH1U, DTH2U, DTBU,

5. Стр. 5 таблицы и схемы — в просмотре

6. Стр. 6 DRU, DSU, DTU, DTHU, DTH1U, DTH2U, DTBU,

7. Стр. 7 таблицы и схемы — в просмотре

8. Стр. 8 LKSR

   Assembly In order to fulfil the requirements for air-tightness class C, the damper must be installed as per ‘Assembly Instruction Rectangular air duct systems’. For the damper, there is the option of adding a motor later on. The damper allows a 50 mm duct insulation without the knob being hidden.…

9. Стр. 9

   Assembly In order to fulfil the requirements for air-tightness class D, the devices must be installed as per ‘Assembly Instruction Lindab Safe’. The devices must be installed with the air flow in the direction of the arrow. The devices allow 50 mm duct insulation without the scale or any motor being…

10. Стр. 10

    DA2EU Setting of flows The two flows are set by moving the end stops. At delivery the stops are set at largest possible distance. If you want to limit the flow span proceed in the following way: End stop screws 0 BELIMO R Made in Switzerland 1. The one flow is set by turning the spindle so that the…

11. Стр. 11

    DAVU Setting of flow limits The two flow limits are set by moving the end stops. At delivery the stops are set at largest possible distance. If you want to limit the flow span proceed in the following way: 1. The one flow limit is set by turning the spindle so that the scale arrow points at the…

12. Стр. 12 Air stream operated dampers

    CARU, CAR Assembly CARU In order to fulfil the requirements of tightness class D the damper must be installed as per ‘Assembly Instruction Lindab Safe’. CAR The damper is installed by simply placing it inside a duct. Measurement The dampers normally don’t need any maintenance. 12

13. Стр. 13 Measuring bends

    MBU, MBFU Assembly In order to fulfil the requirements for air-tightness class D, the bends must be installed as per ‘Assembly Instruction Lindab Safe’. The bends allow 50 mm duct insulation without the measuring points being hidden. For 100 mm insulation, an insulation cup, IK, is available.…

14. Стр. 14 Flow meters

    FMU, FMDRU Assembly In order to fulfil the requirements for air-tightness class D, the devices must be installed as per ‘Assembly Instruction Lindab Safe’. FMDRU must be installed with the air flow in the direction of the arrow. The devices allow 100 mm duct insulation without sticker or measuring…

15. Стр. 15 Flow meters

    FMDU Assembly In order to fulfil the requirements for air-tightness class D, the device must be installed as per ‘Assembly Instruction Lindab Safe’. The device must be installed with the air flow in the direction of the arrow. The device allows 50 mm duct insulation without sticker or measuring…

16. Стр. 16 DIRU

    Assembly Mount the dampers according to “Assembly Instructions Lindab Safe” to meet with the requirements for tightness class C. Consider required straight distance after or before disturbance, as mentioned on the card attached to the measurement nozzles, to obtain accurate flow measurement. Dampers…

17. Стр. 17 DIRU, DIRBU, DIRVU

    To set the air flow (method 1): • Determine the k factor on the scale on the damper, k • Measure the pressure difference by connecting a measuring device to the damper nozzles, Dpm • Calculate the flow by using the formula, q=k · ∆pm • Compare the calculated flow to the required • Adjust the damper…

18. Стр. 18 таблицы и схемы — в просмотре

19. Стр. 19 DIRU, DIRBU, DIRVU

20. Стр. 20 таблицы и схемы — в просмотре

21. Стр. 21 DIRU, DIRBU, DIRVU

22. Стр. 22 DIRU, DIRBU, DIRVU

    Measurement accuracy If the velocity profile is asymmetric, the measurement values can differ from the ideal values. For this reason, the flow meter should never be located right up to any flow disturbance. The method error in the table below will differ, depending on the distance to the flow…

23. Стр. 23 DIRBU, DIRVU

    Assembly The damper which is considered as a component (not ready-to-use-product) are only to be put into operation after it has been built into machines or duct systems and when the system is found to be in conformity with all relevant regulations. Mount the damper according to “Assembly…

24. Стр. 24 DIRBU, DIRVU

    The product normally doesn't requires any maintenance but before maintenance, service or repair make sure that: • power supply is interrupted (all-pole circuit breaker) • observe personnel safety regulations Do not use high-pressure cleaner when cleaning the damper. Care must be taken during…

25. Стр. 25 DIRBU, DIRVU

    DIRBU Technical data for the motors Power supply ����������������������������� Power consumption ������������������ For wire sizing ��������������������������� Connection �������������������������������� Operating angle ������������������������� Torque at rated voltage ������������� Direction of…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.