Инструкции на Активные климатические балки Lindab серии Plexus для вентиляции и кондиционирования

Текст инструкции

1. Стр. 1

   Service & maintenance

2. Стр. 2 1.0 Installation

   1.1 Product description Plexus is provided with fixed lamellas which controls the primary air into non-parallel jets in a 360 degree air pattern. The 360 degree air pattern results in shorter air throws and a draft free indoor climate. Plexus can be used for both cooling, heating and ventilation.…

3. Стр. 3 1.5.1 Push-on fittings

   Please ensure that all pipes and fittings are undamaged, as even small dents and scratches potentially pose a risk of leakage in the system. Always remember to do a pressure test after assembly of the pipe work. Both flow and return pipe is covered by a plastic or rubber protection cover, which…

4. Стр. 4 Push-on valve

   Notice! The connection pipes are internally soft-welded why it’s not allowed to solder the beam to the pipes. 1.5.2 Compression fitting Please ensure that all pipes and fittings are undamaged, as even small dents and scratches potentially pose a risk of leakage in the system. Always remember to do a…

5. Стр. 5 –– The copper insert should be placed inside the pipe on the beam. Always support

   the copper pipe coil when inserting the copper insert into position. Mount a compression coupling and/or a valve to the pipe. Don’t stress the nut too much, since this may crush the pipe. Notice! The connection pipes are internally soft-welded why it’s not allowed to solder the beam to the pipes.…

6. Стр. 6

   After removing the protection cover, make sure that the pipe is intact and undamaged, especially at the pipe end. Crocked or in other ways imperfect pipe ends will result in leaks. Deburr the pipe on the inside and the outside, using a deburring tool before installation Mount a push-on fitting to…

7. Стр. 7 2.0 Commissioning

   2.1 Product labeling Plexus I Fig.1: Label location exterior (Air connection end), Fig.2: Label location interior (On faceplate, water connection end). Plexus F Fig.1: Label location exterior (On plastic wrapping), Fig.2: Label location interior (On faceplate, water connection end). Plexus F Fig.1…

8. Стр. 8 2.2.1 Measure the static nozzle pressure

   To measure the air pressure, a manometer, analog or digital (such as the Lindab PC410) will be needed. Insert the measuring tube onto the specialized measuring nozzle Read off the static nozzle pressure from the manometer 2.2.2 Calculating the airflow After measuring the static nozzle pressure, read…

9. Стр. 9

   Position of JetCone adjustment pins Δpt [Pa] Plexus H60 2 qa [l/s] qa [m3/h] 200 Position of JetCone adjustment pins 2.3 qa [l/s] qa [m3/h] Changing the airflow Measure the static nozzle pressure Locate the air pressure/airflow diagram on the faceplate, or see diagram 1. Find the mean value of the…

10. Стр. 10 3.0 Maintenance

    3.0 Maintenance The interval of cleaning depends on the indoor environment where the beam is placed. Under optimal conditions the Plexus beams only need cleaning every 5 years. 3.1 Cleaning instructions Remove the faceplate Clean underneath the battery with a vacuum cleaner and a piece of wet cloth…

11. Стр. 11 4.0 Product and system specification

    4.1 Material data Plexus I 60 Plexus I 120 Plexus F 60 Plexus F 120 Weight, kg/st 11.6 21.4 17.2 31.7 Water content, cooling, l/m 0.83 2.08 0.83 2.08 Water content, heating, l/m 0.17 0.41 0.17 0.41 Water content, cooling only, l/m 1.0 2.5 1.0 2.5 Copper pipes, quality EN 12735-2 EN 12735-2 EN…

12. Стр. 12 4.4 Water quality

    The water preparation and maintenance for the chilled beam water circuit should be handled by a specialist To prevent corrosion, the water circuit must be airtight The water system must also be equipped with aerators to remove any build-up air in the system. The water should be oxygen free, to…

13. Стр. 14 Support

    Hjælp Hjälp Tuotetuki Unterstützung Supporto UK - Here you can find product updates/mounting instructions and support telephone number/mail. www.lindab.com Right to alterations reserved. DK - Her kan du finde seneste produkt opdateringer/montagevejledninger samt support tlf. nr/mail. www.lindab.dk…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.