Инструкция на Котёл настенный газовый Nova Parva (M90.24A, M90.28A) бренда Biasi

NOVA PARVA

MODELS – VJLTKB M90.24A M90.28A USER MANUAL AND INSTALLATION INSTRUCTIONS ТЕХНИЧЕСКОЕ РУКОВОДСТВО И ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ

Congratulations on your choice

Поздравляем Вас с Вашим выбором Your boiler is electronically controlled and has electronic ignition. Ваш котел управляется электроникой и имеет электронный розжиг The materials it is made of and the control systems it is equipped with give you safety, a high level of comfort and energy savings to…

is fitted with all the safety and control devices required by the current Regulations; Ensure that the installer has connected the pressure relief valve outlet to a drain pipe. The manufacturers are not responsible for damage caused by opening of the pressure relief valve and consequent escape of…

must not be touched by children or by those unfamiliar with its operation; must not be exposed to weather conditions Boiler installation and commissioning tips ¾ Keep the boiler clear of dust during installation and in particular do not allow any dust or debris to enter the top of the boiler where…

If the boiler is fitted with a digital programmer, when setting the times for automatic operation, remember that for every “ON" time there must be an “OFF" time to follow and that on every occasion you enter a time you must also indicate which days that you want the boiler to follow the timed…

Appliance description 1. 1.1 Overview Описание устройства 1.1 Вид Fig. 1.1 1. 2. 3. Case front panel Control panel Control panel cover 1. 2. 3. Передняя панель корпуса Панель управления Крышка панели управления 1.2 Control Panel 1.2 Панель управления 4. 4. Термоманометр с-мы отопления 5. 6. 7. 8.…

Fig. 1.2 bottom view of the boiler/ Рис.1.2- вид котла снизу 1.4 Techincal data 1.4 For detailed technical data see section 4.4 or 4.5 of this manual. Для более детальной информации см. разделы 4.5, 4.6 настоящего руководства. Fig. 1.3 2 Технические характеристики 4

1.5 Operation lights

1.5 Индикаторы функций Three lights (9 in Fig. 1.3) give detailed indication regarding the operation of the boiler. The following table gives the relationship between each of the possible light combinations and their meaning. Три лампочки (9 на рис.1.3) дают подробную информацию о работе котла.…

Lamp OFF

Индикатор горит 4 Lamp ON не Индикатор горит Flashing lamp, alone or Flashing lamp, alternate with simultaneously with an other another lamp. lamp. Индикатор моргает один Индикатор моргает или одновременно с поочередно с другим другими индикаторами индикатором

Инструкция

эксплуатации по 2.1 Warnings 2.1 Предупреждения In order to guarantee safety and correct operation, it is essential that all the tests are carried out by a competent and responsible service engineer before lighting up the boiler. Чтобы гарантировать безопасную и правильную работу котла, перед его…

2.2 Refilling procedure

2.2 Заполнение системы Jnrhsnm Open 11 Close Pfrhsnm Fig. 2.1 Isolate the boiler fro the electrical supply at the fused spur. 1. Open the c.h. circuit filling valve 11 (Fig. 2.1) until the pressure reaches the normal filling pressure as shown in Fig. 2.2. 1. 2. Normal filling pressure = 1bar…

Always ensure that the pressure gauge is set

at the required pressure. Следует периодически показания манометра 2.3 Ignition 2.3 Розжиг 1. 1. Check that the taps located in the lower part of the boiler are open (Fig. 2.3). проверять Проверьте, чтобы краны, расположенные в нижней части котла были открыты (Рис. 2.3.) Open position gjkj;tybt…

2.4 Температура отопления The output temperature of c.h. water is adjustable from a minimum of about 38°C to a maximum of about 80°C (Fig.2.6), by turning the knob (7). Adjustment of c.h. output on the boiler is automatic. The greatest output pre-set in the factory can, however, be reduced in level…

Between -5°C

and +5°C От 5 До 15 градусоь Между-5°C и +5°C градусами From 5°C to 15°C Lower than -5°C Менее -5°C градусоь Fig. 2.7 Your qualified installer will be able to recommend the most suitable adjustment for your system. The temperature and pressure gauge (4, Fig. 1.3) will allow you to check that the set…

Adjustment

It is advisable to adjust the d.h.w. temperature to a level commensurate with the demand, minimising the need to mix with cold water. In this way, the automatic control facilities will be fully exploited. Регулировки Рекомендуется отрегулировать температуру горячей воды в соответствии с ее…

Fig. 2.10 When you expect not to use the boiler for a long period: 1. 2. 3. Switch off the electricity supply to the boiler, by means of the fused spur isolation switch; Shut off the gas supply cock 14 and the cocks for the water circuits fitted under the boiler (Fig.2.11). Empty the water circuits…

Полезные советы

3.1 Central heating 3.1 Центральное отопление For reasonably economical service install a room thermostat. Never shut off the radiator in the area where the room thermostat is installed. Для более экономного использования установите комнатный термостат. Никогда не перекрывайте радиатор в том…

3.3 Periodic maintenance

3.3 Периодическое обслуживание For efficient and continuous operation of the boiler, it is advisable to arrange maintenance and cleaning by an Authorised Service Centre Engineer, at least once a year. Для эффективной и продолжительной работы котла, мы рекомендуем производить обслуживание и чистку…

5 Fig. 3.2 For the first lighting up and following maintenance procedures for the gas supply, it may be necessary to repeat the resetting operation several times so as to remove the air present in the pipework. If noises due to air bubbles are heard during operation... you should check that the…

The likely causes may be impurities caught in

the domestic hot water flow switch filter or limescale deposited in the domestic hot water heat exchanger. It is advisable to have the appliance cleaned out by an Authorised Service Centre Engineer. If water should occasionally leak from the boiler... shut off the taps positioned under the boiler…

Technical information 4. 4.1 Overview Техническая информация 4.1 Вид 17. D.h.w. temperature probe NTC 17. 18. Main circuit drain cock 18. 19. C.h. pressure relief valve 19. 20. Pump 21. Pump vent plug 22. Automatic valve 23. D.h.w. flow switch 24. Modulation gas valve 25. Primary switch flow 24. 26.…

4.3 Wiring diagram

4.4 Technical Data mod. M90.24A

Domestic hot water Горячая вода 4.4 Технические характеристики М90.24А Maximum temperature Максимальная температура Minimum temperature Минимальная температура Nominal heat input Номининальная потребляемая тепловая мощность Minimum heat input Минимальная потребляемая тепловая мощность Maximum useful…

Gas pressures at the burner

Давление на подаче газа Gas Газ Natural G20 Природный газ G20 Butane G30 Бутан G30 Propane G31 ПропанG31 Pa Па mbar мбар Pa Па mbar мбар Pa Па mbar мбар Min Мин Max Макс Ignition Розжиг 220 1150 600 2,2 11,5 6,0 550 2650 1200 5,5 26,5 12 700 3500 1300 7,0 35,0 13 Gas rate Расход газа Gas Газ Natural…

4.5 Technical Data mod. M90.28A

Domestic hot water Горячая вода 4.5 Технические характеристики М90.28А Maximum temperature Максимальная температура Minimum temperature Минимальная температура Maximum pressure Максимальное давление Nominal heat input Номинальная потребляемая тепловая мощность Minimum heat input Минимальная…

Flue design

Конструкция дымохода Gas pressures at the burner Давление газа на горелке Gas Газ Pa Па mbar мбар Pa Butane G30 Па Бутан mbar мбар Pa Propane G31 Па Пропан mbar мбар Natural G20 Природный газ Min Мин Max Макс Ignition Розжиг 220 1150 600 2,2 11,5 6,0 550 2750 1200 5,5 27,5 12 700 3500 1300 7,0 35,0…

4.6 Hydraulic specifications

4.6 Гидравлические характеристики 0,50 0,40 bar 0,30 0,20 0,10 0,00 l/h Fig. 4.4 The hydraulic specifications in Fig. 4.4 represent the pressure (available head for the central heating system) as a function of the flow rate. The load loss due to the boiler has already been subtracted. Output with…

Capacity Объем kPa Pre-load pressure кПа Предварительное давление Maximum volume water in the system l л bar бар of Максим. объем воды в системе l л 6,0 100 1,0 104 Tab. 4.1 * Where conditions are: Average maximum temperature of the system is 80°C Initial temperature when filling up the system is…

Installation 5. Монтаж 5.1 Warnings 5.1 Предупреждения The use of gas appliances is subject to statutory control; it is essential to observe the current regulations and laws in force. Использование газовых приборов подлежит контролю; следует выполнять установку в соответствии с действующими нормами…

To allow maintenance procedures it is necessary to leave the minimum gaps indicated in Fig. 5.1. - Для проведения работ по обслуживанию котла необходимо оставить минимальное расстояние, как на рисунке 5.1. Fig. 5.1 - When installing the boiler in a cupboard, cover or alcove allow at least 6 cm…

5.4 Overall dimensions

5.4 Размеры Flue pipe axis 24kW Oсь дымохода Flue pipe axis 28kW Oсь дымохода Boiler axis Oсь котлa 18 4 Flue pipe axis Oсь дымохода Boiler front Wall mounting bracket Крепежные скобы Cold water inlet Газ Gas 83 D.h.w. outlet C.h. return Oбратка отопления подача отопления Вход холодной воды D.c.w.…

Mount the boiler on its bracket. Fix the gas cock A (¾") to the boiler using the ¾" gasket (Fig. 5.3) 3. 4. 5. Fix the pipes B (c.h. circuit) to the boiler and the pipe C (gas) to the cock A using the ¾" gaskets. Repeat the above procedure for the d.c.w. inlet utilising the ½" cold water inlet cock…

5.7 Electrical connections

5.7 Электрические подсоединения 1. Remove the front panel of the case (see the section 8.2 in this manual). 1. 2. Remove the screws H and loosen the screws I .(Fig. 5.5). Move the lower part of the side panels as indicated in Fig. 5.6 and pull the control panel. When completely pulled out, the panel…

The room thermostat must be connected to

the terminal block situated next to the control panel. When connecting any type of external control, the jumper K in Fig. 5.8 must be removed. 7. Connect the room thermostat between terminals 1 and 3 as shown in Fig. 5.9 Do not connect live wires to terminals to which the room thermostat must be…

Connect the boiler electrical power by means of the two-pole switch on the plant; the signal LED will flash every 4 seconds. 1. 2. Move the working selection / heating temperature adjustment knob as shown on Fig. 5.13; the signal LED will flash intermittently approx. every 2 seconds. 2. 9 3. 4. 7…

Seconds Секунды Set-up no. N° настройки 8. Fig. 5.15 8. For storing the set parameters, keep the boiler reset push-button pressed for about 5 seconds; the signal LEDs will flash simultaneously, as described on Fig. 5.16 Storage validation Fig. 5.16 Place the selector as shown on Fig. 5.17 to exit…

Commissioning 6. Ввод в эксплуатацию 6.1 Electrical installation 6.1 Монтаж электрической части Preliminary electrical system checks to ensure electrical safety shall be carried out by a competent person. i.e. polarity, earth continuity, resistance to earth and short circuit. If a fault has occurred…

Remove the front panel of the case

(see the section 8.2 in this manual). 2. 3. Unscrew the cap on the automatic air purger valve 22 (Fig. 6.2) one full turn and leave open permanently. 3. 4. Gradually open stopcock at the filling point connection to the c.h. system until water is heard to flow; do not open fully. 4. 5. Open each…

13. Turn on the electricity supply to the boiler, switching on the fused spur isolation switch. The appliance operation light 9 will flash every 4 seconds. Turn the function selector 7 as in Fig. 6.3. The appliance operation light 9 will flash every 2 seconds. 9 12. Включите питание котла на…

5. 6. 7. 8. 9. 10. Loosen the internal screw 37(Fig. 6.4) on the Outlet Pressure Test Point of the Gas Valve and connect a pressure gauge using a suitable hose. Set the d.h.w. and c.h. temperature control knobs to their maximum position. Switch on the boiler and open at least one hot water tap…

Switch off the boiler and re-connect the electrical connector B to the modulator coil. 14. Access the main control panel (see section 5.7, follow steps 2 - 4) 15. Switch on the boiler. 16. Check the ignition gas pressure. Compare the value on the gauge with the value indicated in the sections 4.4…

Fig. 6.5 3. 6 5 3. Connect the boiler electrical power by means of the two-pole switch on the plant; the signal LED will flash every 4 seconds. 4. Keep the boiler reset push-button pressed for about 10 seconds; the blockage LED will start flashing. 4. burner ignition set-up Fig. 6.6 To set the…

70% Default По умолчанию 213 0% 0 255 Power Мощность % Set-up no. N° настройки Fig. 6.7 9. For storing the set parameters, keep the boiler reset push-button pressed for about 5 seconds; all signal LEDs will flash simultaneously, as described on Fig. 6.8 Storage validation Fig. 6.8 Place the selector…

Useful

output central heating Полезная мощность отопления Fig. 6.10 To display the set parameters, keep the boiler reset push-button pressed for about 5 seconds. Signal LEDs will flash as many times as set by the parameters. Для отображения установленной настройки, держать нажатой кнопку перезапуска…

For storing the set parameters, keep

the boiler reset push-button pressed for about 5 seconds; all signal LEDs will flash simultaneously, as described on Fig. 6.14 Fig. 6.14 Storage validation Place the selector as shown on Fig. 6.15 to exit the programming. 3. Для занесения в память установленной настройки, держать нажатой кнопку…

Take the User step by step through the

lighting instructions. Show the User how to switch off the appliance quickly and indicate the position of the electric supply isolator. Explain the proper use and adjustment of all system controls; this will ensure the greatest possible fuel economy. Explain the function and use of the function…

Gas conversion 7. Смена типа газа 7.1 Warnings 7.1 Предупреждение Procedures to adapt the boiler to the type of gas available must be carried out by a competent and responsible person. More detailed instructions, relating to the procedures for adapting the boiler to the type of gas available and…

Fig. 7.1

2. To enter the programming phase, connect the boiler electrical powering by pressing the two-pole switch then place the working selector / heating temperature adjustment knob, see Fig. 7.2 to OFF 2. Для доступа в режим программирования, необходимо подключить электропитание к бойлеру при помощи…

U

Legends LED of Условные обозначения Выключенный светодиод U U U LED on Светодиод постоянно горит LED flashing or flashing with another LED simultaneously LED flashing in turn with another LED Светодиод мигает или одновременно мигает с другим Светодиод попеременно мигает с другим светодиодом Set the…

To change the set-up, turn the sanitary fixture temperature adjustment knob to the correct position Fig. 7.5, the signal LED for boiler blockage flashes quickly. 8. For storing the set parameters, keep the boiler reset push-button pressed for about 5 seconds; all signal LEDs will flash…

Maintenance 8. Описание котла 8.1 Warnings 8.1 Предупреждения The procedures detailed in this chapter must be carried out only by a professionally qualified person. Thus you are advised to contact an Authorised Service Agent. Действия, описанные в данной главе, должны выполняться только…

Loosen the screws B. Bring the bottom

of the panels away from the boiler and lift them, freeing them from the top hooks (Fig. 8.2). 3. Ослабьте винты В. Отодвиньте нижнюю часть панелей от котла и приподнимите их, освободив от векхних крючков (рис 8.2). 8.3 Emptying the d.h.w. system 8.3 Опорожнение горячей воды 1. 1. Turn off the d.c.w.…

8.1. Checking the pressurisation in

the expansion vessel 8.1. Проверка давления баке Empty the central heating system as described in section 8.4 of this chapter and check that the pressure in the expansion vessel is not less than 1 bar. See also section 4.7 of this manual. Опорожните систему отопления, как указано в разделе 8.4 этой…

Fig. 8.5 3. 4. 5. Make sure the room temperature thermostat is set to “richiesta calore” (heating demand) Keep the reset push-button pressed for about 10 seconds; the boiler blockage LED will start flashing. 3. To set the Spazzacamino mode, the signal LEDs should be displayed as shown on Fig. 8.6 5.…

MIN. VALUE

МИНИМУМ MAX. VALUE МАКСИМУМ Fig. 8.8 To exit the programming, move the working selector / heating temperature adjustment knob to “Winter” position, as shown on Fig. 8.9 Для выхода из режима программиирования установить Переключатель режима работы / Рукоятку регулирования температуры отопления в…

Disconnect power supply to boiler, set

the DIP switches of the board as shown in the Fig. 8.11 2. Отключите подачу электрического питания к котлу, настройте «впаиваемый в печатную плату пакет миниатюрных переключателей» платы, как показано на Fig. 8.11 ON 1 ON ON OFF ON Fig. 8.11 OFF Fig. 8.12 3. Turn the boiler on and, before performing…

Инструкция на Котёл настенный газовый Nova Parva (M90.24A, M90.28A)

Текст инструкции

Новое в каталогах

Новое в инструкциях