Инструкция на Осевые вентиляторы Rosenberg среднего давления
Осевые вентиляторы Rosenberg серии AND / ANE / AND со стандартным двигателем. Инструкция по эксплуатации.
Загружаем документ…
Текст инструкции
-
/ SAFETY / Industrial Safety Symbols . The following symbols refer to particular dangers or give advice for save operation. ! ! ! Caution! Danger! Safety Advise ! " " # #! Danger from electric current or high voltage! # $ ! &% " '( " Explosive atmosphere! #! Crush Danger % # ! #" & Danger! Do not…
-
/ Safety advice # Rosenberg " & &' $$ & " ! ) , $& , $ * AN.. # # * ! % " - ' - , " & &' ! # &! - , "& ! ' # &' # . Rosenberg explosion proof radial fans are produced in accordance with the latest technical standards and our quality assurance programme which includes material and function tests…
-
- The standard axial fans of the AND / ANE / AND Ex series with bilateral mounting
flange are not equipped with a shock-hazard protection, since their preferred place of installation is in tubing systems. * When installing the fan, always make sure to verify that the impeller may not be touched. If this may not be excluded altogether, then the installation of a hazardshock…
-
" IEC * „e“, " ), " T1 IP 55 / T3 (T4 F (+40°C). * # - " - ! # , ! " , , % " " , " # " ", # # .! # , % " "# - # " . Ex - protected high performance fans are especially developed / maufactured for the use in areas containing explosive mediums. The used Normmotor are ignition protected standard “e”…
-
Axial fans with adjustable blades are suitable for the conveying of
− clean air − slightly dusty and greasy air − slightly aggressive gases and fumes (please refer to our engineers) 3 − mediums up to an atmospheric density of 1,3 kg/m − mediums passing throught with a temperature of - 30 °C up to + 40 °C (please take into account the specifications of the motor…
-
, " , # , . • Store the fan on a dry place and weather protected in ist original packing. − Cover open paletts with a tarpaulin and protect the fans against influence of dirt (i.e. stones, splinters, wires, etc.). • Storage temperatures between - 30 °C and + 40 °C . • With storage times of more than…
-
# ) 24167. . ) % ( ( ' ) # % - # - ,1 # % #. # % '! &! % ) ) % # DIN % # # % ( # %1 #! %#( #! - - # % DIN 31001 , % &). - - Prevent falling objects and foreign matter from entering inlet and outlet opening of the fan. The protection guards must be certified to DIN 31001 or DIN 24167. The unpacked…
-
+ % #&$ & # Rosenberg ! : ) # # - &! ! In order to avoid any overloading, please contact Rosenberg prior to performing any adjustment of the blade position. For all design sizes: Rebalance the impeller after any alteration of the blade position. / . 1: ! : Illustration 1: Blade adjustment…
-
. " AN.. 315 – 1000: The angle is adjusted by means of a protractor - Place the impeller hub on a flat surface with the rear pointing downwards. Use the bottom face of the hub as the reference plane for the adjustment of the angle. - Loosen the mounting screws between the hub sections until the…
-
Connect the electrical system in accordance with the technical prerequisites at
the place of installation and the applicable regulations on the basis of the wiring diagram enclosed resp. the specifications of the motor manufacturer. - Introduce the cables properly into the terminal box and seal (if required, provide for a “water pocket”). Motor protection either by means of a…
-
% ) % '! # # ! Do not utilise any metal compression glands in a plastic terminal box! % : ( # % & ) &( % ! Additional requirements in case of explosion protection: Use only approved compression glands! % • # ( #: " − ! − " . # " − ( • ) ( ), " " # ) ( ( Z1 (# ) Z2 ( ) (→ → • Before control of…
-
2 3+ 4 5 / OPERATION 2 & * # % # % - & * &! # & &'( " , , ) % % ' # ( (1 # - ) ! ( → ! ' -) % % ( # ! ( . : S1! % #! % & ! Operation of the fan only through qualified and supervised workers under the known references! Only commence operation when it is installed in accordance with references ! * The…
-
− " − − ( ), " * ' ? # ( − • − % & " 3- " , , , , - ) • Prepare fan for first operation − correct mechanical installation − electrical installation in accordance with regulations − remove foreign matter from inlet and outlet area and from inside of fan − protection guard (3accessories) installed, no…
-
/ MAINTENANCE 3+0 ) & % & - # % -! * % − & #: # - - % . '! − % % # ! ) " '! #! Maintenance of the fan only through qualified and supervised workers under the known references! Before any maintenance work is undertaken: − Stop fan in accordance to regulations and disconnect all poles from mains…
-
Do not flood motor! Do not bend impeller, blades! ( − ) ( # " ", , - " " ) # " − # " "# − # " "( ) - If available, open the inspection port, if not, remove the fan from the tubing system (* before removing the fan bracket, disconnect the power supply and support the fan). - Clean the inlet opening…
-
/ REPAIR . / . % # % : % − # - -! & * - % . '! − % % # ! ) " '! #! Repair of the fan only through qualified and supervised workers under the known references! Please note the following before any repairs are undertaken: − Stop fan in accordance to regulations and disconnect all poles from mains…
-
" − , ) " − − 2 " # − "# " "# " - # "# " - " − ! " " "# - " , " : 1 - " " − " " 1% 2 " "# . " , " - # " ( → ). • Replacing the impeller − Disconnect the power supply of the fan. − Remove the protective grating on the inlet side and the tamper protection or remove the fan from the duct system, using…
-
Install the fan in the duct system, if required, reinstall the protective grating and reconnect the power supply (Õ cf. “Assembly”). % "% • # − − * " # "% − − − − − * ( * ! * . " " (→ "# ) (→ "# ) ,# "# " " " " " " " "# " − − #: " " − − " % 0 "# " . "# : 1 - " " " " − # 1% 2 " "# . , " ( → " - " ).…
-
- Align the impeller / motor unit so ensure a uniform ring gap between the impeller and the housing
- - In case of explosion protection: The minimum clearance between rotating and fixed components must be at least 1 % of the outer diameter of the impeller, the absolute minimum, however, is 2 mm. Tighten the mounting screws of the motor. Turn the impeller by hand to verify the freedom of movement…
Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.