Инструкция на Контроллеры Gateways
M-INTERFACE Gateway. Инструкция по установке и эксплуатации.
Смотрите также: Инструкция по эксплуатации →
Загружаем документ…
Текст инструкции
-
INSTALLATION & OWNER’S MANUAL
M-INTERFACE Thank you very much for purchasing our product, Before using it, please read this manual carefully and keep it for future reference.
-
■ Please entrust the distributor or professionals to install the unit. The
Warning Delegate installation installers must have the relevant know-how. Improper installation performed by the user without permission may cause fire, electric,shock, personal injury or water leakage. ■ Please do not strike down the M-INTERFACE gateway controller, otherwise it may lead to abnormal…
-
NOTE
■ Do not install near a place leak flammblble gas easily, otherwies it may cause fire; ■ Wiring according to the instruction manual, do not press the terminals, otherwise it may cuase electricity leakage, wire broken, overheat, and fire. Before careful read this manual, do not connect the control…
-
2) Side view of M-INTERFACE gateway controller (Unit: mm) 319±1 Fig.3-2 3) Detailed drawing of installation holes (Unit: mm) ■ Install at a place where should not affect by electromagnetic wave or dust; ■ Avoid to install at a place where affects by sunshine or heat source device etc; ■ Avoid to…
-
M-INTERFACE gateway controller is used for query and controls the air-conditioning indoor unit, and transmits the status information of indoor unit to the computer and transmits the controlling and querying orders sent by the computer to the indoor unit. 1) M-INTERFACE gateway controller indication…
-
2) Terminal figure
LAN terminal I/O terminal XYE Console terminal K1K2E Fig.3-6 3) LED indication lamp instructions Table.3-1 Indication lamp Color Indication lamp instructions TX1~TX8 Yellow No.1-8 sending terminals indication lamp RX1~RX8 Green No.1-8 receiving terminals indication lamp Power Red Power indication…
-
4) Specification parameters of M-INTERFACE gateway controller
Table.3-2 Power specification Using conditions Capacity Voltage range Single phase AC 100~240V, 50/60 Hz Consumed power Max.15W Voltage fluctuation Rated value ±10% Ambient temp. -10~50℃ Ambient humidity 0~95% Storage temp. -20~60℃ Insulated resistance When it is DC 500VM, it will over 50MΩ Weight…
-
7) IO terminal
Table.3-4 Gateway controller Base pin name Function definition Pin1 Gateway controller error output; Pin2 When the device operates normally, break off Pin1 and Pin2, close Pin2 and Pin3; when it is error, close Pin1 and Pin2, break off Pin2 and Pin3. Pin3 Pin4 Pin5 IN1 IN2 E Pin6 When it’s powered…
-
4.1 M-INTERFACE Network
1)M-INTERFACE gateway can connect the local area network or Internet network through LAN terminal. M-INTERFACE network topology as follows Fig 4-1. 2)M-net terminals are listed to be two rows, 1-4 are XYE terminals, 5-8 are K1K2E terminals. Computer or other similar devices can visit M-INTERFACE WEB…
-
4.4.1 IP configuration
Default IP of gateway is 192.168.100.40, subnet cover code is 255.255.255.0. IP address of computer or similar devices should manual configure the statistic IP and within the range of 192.168.100, subnet cover code should be 255.255.255.0. If the computer only insert the MINTERFACE network, then use…
-
Fig.4-3
Type “ipconfig” in the above figure, then the interface will display the local dynamic IP address, and it will write this IP address into the property dialogue box, and finish the statistic IP address configuration, details please consult the local network administrator. After the statistic IP…
-
4.4.2 Local LAN access
If there is a computer or other similar device of same subnet area as M-INTERFACE in LAN, then type the link address of M-INTERFACE gateway (e.g.: http://192.168.100.40) on the browser address bar can visit the M-INTERFACE WEB interface to operate the air-conditioning device. The local visit…
-
2) Network terminal mapping
If the company has a public network address, then it needs to send a mapping of a terminal in fire wall to M-INTERFACE gateway; when the computer or similar device of outside network visit the M-INTERFACE, then take http:// public network IP: visit as a terminal. E.g.: http:// 203.208.60.72:6080.…
-
4.6 WEB functions introduction
WEB system has “Device monitoring”, “System mapping”, “Setting”, “Device information” and “Help” etc. functions. Fig.4-10 1)Device monitoring Offer indoor and outdoor units’ operating details and control the indoor unit. 2)System mapping Display the entire situation of refrigerant system; include…
-
5. SETTINGS
Do the following settings before using the M-INTERFACE gateway. 5.1 M-INTERFACE setting M-INTERFACE gateway setting as the following display: Fig.5-1 5.2 Time setting Offer M-INTERFACE gateway system time synchronization function, display as follow: Fig.5-2 Select the time area, click the “OK”…
-
5.3 IP setting
If add the M-INTERFACE into local network, then it needs to reset the M-INTERFACE IP address, and click “OK ” button after setting. If many M-INTERFACEs in the same network area, then the IP address could not be repeated. Fig.5-3 5.4 FTP setting Set the IP address, terminal, login name (Default…
-
6. OPERATION INSTRUCTIONS
6.1 User login Type the link address of M-INTERFACE gateway on the browser address (take windows 7 system, IE for example), then can visit the M-INTERFACE WEB login interface. Fig.6-1 Enter the login page, user operates as follow to enter into system: 1) Select user name, type in password; 2) Select…
-
6.2 Main interface introduction
WEB home page display as follow: Main menu Submenu Information display Fig.6-2 Home page: main menu, submenu and information display. Main menu: display all functions of system, include “Device monitoring”, “System mapping”, “Setting”, “Device information” and “Help” etc. functions. Submenu: simple…
-
The operating statuses of indoor unit are cool, heat, fan, OFF, power off, error and lock. Different
operating statuses will has different pictures. Click a single indoor unit, then it will display the operating status information of this indoor unit on the bottom of page, include ON/OFF status, operating mode, device name and HP etc. information. 2)Control the operating status of indoor unit Click…
-
6.3.2 System monitoring
Display all the indoor units of refrigerant system as the system way, has the function of checking and controlling the operating status of indoor unit. 1)Check the detailed information of indoor unit Fig.6-6 Select the refrigerant system, the page will display all the indoor unit of the refrigerant…
-
Click the “
” button in the page, then can control the indoor unit operating status page. Select one or more air-conditioners, set the controlling parameters, include “ON/OFF setting”, “Mode setting”, “Swing setting”, “Temp setting” and “Fan speed setting”, and then click the “Send” button to send the control…
-
6.4 System mapping
Display the entire situation of refrigerant system, to reflect the mapping relationship between the indoor and outdoor units. Fig.6-8 Select a single refrigerant system, the page display all the indoor unit pictures of this refrigerant system, and the bottom of the page display the indoor unit…
-
Fig.6-9
Click “OK” button after changing. 6.5.2 Refrigerant system mapping Output the topology document, the auto topology structure as follow display: Fig.6-10 Installation & Owner‘s Manual 23
-
6.5.3 Gateway controller status
Display the status information of gateway controller. Fig.6-11 6.6 Device information Check the indoor/outdoor device information in the refrigerant system. 6.6.1 Indoor unit information Select the refrigerant system, click the “Indoor Info”, and the will show up the indoor unit information display…
-
The display contents include: serial port (terminal no. which inserted into), address, physics location, sales model, fan power, E-heater power and maintenance status information. 6.6.2 Outdoor unit information Select the refrigerant system, click the “Outdoor Info”, and the will show up the outdoor…
-
7. TROUBLESHOOTING
7.1 Unable to enter into the login page Type the IP address of M-INTERFACE gateway in the browser, if it cannot display the login page, which may be error of network; if it’s needed, ask the IT administer to check the local network. Check the computer whether stay the same network area with the…
-
2)Wrong password
When the password was wrong, it would display as follow: Fig.7-2 Type the correct password again. 7.3 No device displayed If login successfully, and no data display in the home page, then contact the dealer or technicians to check whether the wiring of M-net communication terminal was correct, and…
Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.