Инструкция на Контроллеры Gateways
Интеллектуальная система управления IMM. Инструкция по эксплуатации.
Смотрите также: Инструкция по эксплуатации →
Загружаем документ…
Текст инструкции
-
OWNER'S MANUAL
Instruction manual for New generation Air-conditioning network intelligent manager system Thank you very much for purchasing our product, Before using it, please read this manual carefully and keep it for future reference.
-
1. IMM INTRODUCTION
1.1 IMM system introduction IMM system is the short name of Intelligent Manager. It consists of three parts: IMM software, Minterface web gateway and V4+ outdoor unit refrigerant system. The IMM system can connect 4 Minterface gateways at most, totally could join up 64 refrigerant systems. The IMM…
-
1.3.1 Local network connection
The cline-side can connect to the server through the local network, the local network connection as the following display: Fig.1-2 1.3.2 Remote network connection The client-side and server also can use the remote network (VPN) connection. VPN has router establishing and computer establishing…
-
1.4 IMM software functions
User can operate the IMM client-side software to monitoring the air-conditioning system. The functions offered by IMM software as the following display: Fig.1-5 Main functions as follow: 1) Device monitoring Offer control and management of indoor/outdoor unit for the M-INTERFACE gateway. 2) Schedule…
-
2. SOFTWARE INSTALLATION
2.1 Installation preparation Before the IMM software installation, it needs to make sure the air-conditioning system operated normally, M-INTERFACE gate way worked normally, the communication between M-INTERFACE gateway and air-conditioning system was normal, and it needs to meet the following…
-
3. SETTING
3.1 IP address setting Default IP of M-INTERFACE gateway is 192.168.100.40, subnet cover code is 255.255.255.0. The M-INTERFACE gate and IMM server must be stayed in the same sub network, two ways of realization: amend the M-INTERFACE gate IP and configure the static state IP for server. 3.1.1…
-
2) Configure several IP
Before configure several IP, it need to configure a statistic IP address. Open the property dialogue box, select the “Advanced”, and display the TCP/IP setting dialogue box as follow: Fig.3-2 Click the “Add” button in IP address bar, add a IP address in the same net area with “192.168.100.40”…
-
Fig.3-3
After typing, click “OK” to save. Do not conflict with other IP in the network, detailed IP address assignment needs to consult the network administrator. 3.2 Software operation setting Before software operation, set the server software, client-side software and database software. Detailed setting…
-
4. OPERATION INSTRUCTION
4.1 User login Operate the IMM client-side software, popup the login interface as the follow display: Fig.4-1 After “Connect to the server successfully” was displayed at the lower left of the login interface, then can carry out the login operations. Steps of carrying out the login operations as…
-
Fig.4-2
4.3 System initialization After the user login successfully, then will show out the system initialization dialogue frame, and carry out the initialization of the whole system, update the system information. The itialization dialogue frame display as follow: Fig.4-3 Owner‘s Manual 9
-
Click the “Re-initialization” button, then it will re-initialize from the current time. Click the “Exit the system” button, then will stop the initialization work and exist the system. 4.4 Main interface introduction The system home page display as the follow: Menu Function Display Information tip…
-
4.5.1 M-INTERFACE gateway monitoring
Choose the M-INTERFACE gateway selection; the interface will display all the M-INTERFACE gateway devices in the IMM system. Fig.4-5 There are 3 display statuses of M-INTERFACE gateway: lost connection, locked and selected. When selected or right mouse click a M-INTERFACE gateway device, the bottom…
-
After successfully set “Limit mode”, the device icon will add an icon with locker
Parameters specifications: Table.4-1 Parameters Specifications Limit mode Locked: can not operate in the WEB page of M-INTERFACE Un-locked: Remove the locking of M-INTERFACE gateway device. Emergency stop ----: Not carry out the emergency stop function. Stop: Carry out the emergency stop function…
-
The outdoor unit display status: error, lost connection, cooling, heating and selected. Select or
right mouse click a outdoor unit, then check the on and off status, ambient temperature, ammeter readings etc. detailed information of this device in the “Device details information”. Icon specifications: Icon Specifications Table.4-3 Icon Specifications Icon Specifications Outdoor unit lost…
-
Fig.4-9
Displayed detail information: on and off status, operating mode, device name and device number etc. 2)Control the operating status of indoor unit Choose the “Device control”, select one or more sets indoor units (selecting method refers to 4.5.4), in the bottom of the interface configure parameters…
-
The interface will display the icons which wait for being sent, after the order execution, the icons will disappear, and the interface will be refresh, then can view the operating status of the control order had been executed. If control failed, the “Prompt message” in the interface bottom will…
-
Function shortcut keys operations
Right-click the Selected icon, then it will popup the selection frame of “All select/cancel all select”, choose “All select” and “Cancel all selected” to select and cancel quickly. The operation steps as follow: 1)Select the “indoor unit” or “outdoor unit” class (or primary group or secondary…
-
Fig.4-13
Click the “Non-selected device” option, select the device and click the “add” button. Click the “Selected device” option, and then it shows up the selected devices. Choose the relative devices, and click “Move” to move the devices into “Non-selected device”. After selection, click ”OK” and then…
-
■ Control parameters setting
Fig.4-15 Set the time, on and off status, mode, fan speed, temperature, swinging parameters. Click the cancel icon to cancel the setting. ■ Time selecting There are two ways of adding time: Choose date or week. Date: Click the date under corresponding month, select the month and date which displayed…
-
Fig.4-17
The upper left corner of the page will display the added schedule name. And the right displayed the added device. If it’s the first time setting schedule of the device, then the icon will add the schedule icon. Use the “Data statistics” to check the execution status of the schedule. 4.7 Energy…
-
The left side will display the indoor unit group information, and select one or more sets indoor units and choose the energy saving option, then click the “Set” button. After setting, the air conditioner icon will display the locked icon. If it needs to remove the limit, then choose the “Remove”…
-
If the user needs this function please consult the dealer, and get the activation code to activate this function. The activated page as following display: Fig.4-20 Select the “Start time”, “End time” and “Calculate device” parameters, and then click the “Calculate” button, then the page will display…
-
Click the “Setting” button, popup the dialogue frame, to set the single electricity price and the multistep electricity pricing. Click the “Export” then it will export the displayed results to the xls/txt/csv form.The xls form display as follow. Fig.4-22 Click the search icon, and carry out the…
-
Fig.4-24
Find the relative air conditioning device in the operated device, click the “as public device” or “as idle device” button, and divide it to the public device or idle device. Idle device means the devices are not used; public device means the devices in the public place, such as air-conditioning…
-
2)Click the relative group option, the corresponding device in the group will be displayed in the right of the page. ■ Add group: The adding group method of the outdoor unit is the same as the indoor unit (Take adding the secondary group of indoor unit): Fig.4-26 Click the primary group “ Building”…
-
Fig.4-29
The left page will display all the gateway devices and their terminals, click the relative terminals, the right of the page will display the air-conditioning device under the terminal; 1-4 are indoor unit terminals, 5-8 are outdoor unit terminals. 4.11 Data statistics Calculate the operation…
-
Select the “Start time”, “End time” and “Device class” parameters, and then click the “Calculate”
button, then the page will display the result. Display as follow: Fig.4-31 Click the search icon in the calculation page, and the result will be displayed in the page. Such as type in “41106”, then the page will display the searching results as follow: Fig.4-32 Owner‘s Manual 26
-
Click the “Export” button; export the page result to the xls/txt/csv form, the xls form display as follow: Fig.4-33 4.12 Log Display the IMM system operation records by all the user. Fig.4-34 Select the “Start time”, “End time” and “Log type” parameters, the Log type has: orders, schedule, and…
-
Fig.4-35
Click the search icon, and carry out the searching function. Such as type in “user”, then the page will display the searching results, display as follow: Fig.4-36 Owner‘s Manual 28
-
Click the “Export” button; export the page result to the xls/txt/csv form, the xls form display as
follow: Fig.4-37 4.13 Prompt message Display the failed control operation records and the connecting information between client-side and server; when the operation failed, prompt message icon will be red. User can click “Prompt message” icon to check the relative information, the prompt message…
-
Fig.4-39
After the alarm situation removal, the alarm frame will display the alarm has been removed. Click a prompt message, the page will display details of this information. If check the “Popup the newest prompt”, then it will automatically popup this prompt frame when there is prompt message. When there…
-
Carry out the login operation when it is not connect the server, the result be displayed as the above; it should check the client-side configuration information and the network of the server and client-side. 2) Wrong password Fig.5-2 The above figure means the password was wrong. It needs to re-type…
-
6. APPENDIX
6.1 Error code analysis of client-side interface The following error code tables are suitable for the V4+ series indoor and outdoor units. When there was error please contact technicians for maintenance immediately. Indoor unit error code table: Table.6-1 E0 Wrong phase order or none phase P1 Anti…
-
Table.6-2
Outdoor unit error code table: E0 Outdoor unit communication error P2 Protection for low air exhausting zpressure E1 Wrong phase order or none phase P3 Compressor current protection 1 E2 Indoor unit communication error P4 Temperature protection of air exhausting pipe E3 Air exhausting temp. sensor…
Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.