Инструкции на Активные климатические балки Lindab серии Premum для вентиляции и кондиционирования

Текст инструкции

1. Стр. 1

   Service & maintenance

2. Стр. 2 1.0 Installation

   1.1 Product description Lindab’s supply air beam Premum can be used for cooling, heating and ventilation. Water valves, actuators, Regula Secura, Regula Combi and Regula Connect can all be built into the Premum beam. Premum feature the Lindab JetCone, a innovative way of regulating air volume. The…

3. Стр. 3 1.5.1 Push-on fittings

   Please ensure that all pipes and fittings are undamaged, as even small dents and scratches potentially pose a risk of leakage in the system. Always remember to do a pressure test after assembly of the pipe work. Both flow and return pipe is covered by a plastic or rubber protection cover, which…

4. Стр. 4 Push-on valve

   Notice! The connection pipes are internally soft-welded why it’s not allowed to solder the beam to the pipes. 1.5.2 Compression fitting Please ensure that all pipes and fittings are undamaged, as even small dents and scratches potentially pose a risk of leakage in the system. Always remember to do a…

5. Стр. 5 –– The copper insert should be placed inside the pipe on the beam. Always support

   the copper pipe coil when inserting the copper insert into position. Mount a compression coupling and/or a valve to the pipe. Don’t stress the nut too much, since this may crush the pipe. Notice! The connection pipes are internally soft-welded why it’s not allowed to solder the beam to the pipes.…

6. Стр. 6

   After removing the protection cover, make sure that the pipe is intact and undamaged, especially at the pipe end. Crocked or in other ways imperfect pipe ends will result in leaks. Deburr the pipe on the inside and the outside, using a deburring tool before installation Mount a push-on fitting to…

7. Стр. 7 2.0 Commissioning

   2.1 Product labeling Fig.1: Label location exterior (water connection) Fig.2: Label location interior (battery end). On the label you’ll find: Order: Order identification number. Pos: Order position. Product: Product configuration. Project: Project name. Mark: Marking noted on order. Nozzles: Number…

8. Стр. 8 2.2.2 Calculating the airflow

   After measuring the static nozzle pressure, read the setting of the four pins in the corners to find the mean value of the pins. Locate the diagram on the faceplate or see diagram 1-2, and use the static nozzle Inregulation Diagram pressure andPremum/Premax the mean value of the pins to find the…

9. Стр. 9

   Changing the airflow Measure the static nozzle pressure Locate the air pressure/airflow diagram on the faceplate, or see diagram 1-2. Find the mean value of the four pins to reach the desired airflow, in the diagram on the faceplate. Use the static nozzle pressure and the desired airflow to find the…

10. Стр. 10

    30˚ Example Eksempel Exempel Esimerkki Beispiel Esempio Exemple Press and release “clips” from deflector position. Tryk og frigør ”clips” fra deflektor position. Tryck ihop och frisläpp Clipset från luftriktarpositionen. Vapauta pidäkeklipsi ohjaimesta. Klammer zusammendrücken und aushaken. Premere…

11. Стр. 11 3.0 Maintenance

    The interval of cleaning depends on the indoor environment where the beam is placed. Under optimal conditions the Premum beams only need cleaning every 5 years. 3.1 Cleaning instructions Remove the faceplate Clean underneath the battery with a vacuum cleaner and a piece of wet cloth Demount the…

12. Стр. 12 4.0 Product and system specification

    4.1 Material data Premum 4.2 Weight, kg/m 15 Water content, cooling, l/m 0,75 Water content, heating, l/m 0,25 Copper pipes, quality SS/EN 12449 Pressure class PN10 Environmental declaration Please visit www.lindqst.com 4.3 • Select Documentation Finder • Select “Premum” • Select “Environmental…

13. Стр. 13

    The water velocities should not exceed 1m/s, and should be kept as close to the nominal flow as possible to minimize noise and optimize the energy yield There should be used in-line strainers to remove dirt particles from the water. If the water contains any additive inhibitor this must be…

14. Стр. 14 Support

    Hjælp Hjälp Tuotetuki Unterstützung Supporto UK - Here you can find product updates/mounting instructions and support telephone number/mail. www.lindab.com Right to alterations reserved. DK - Her kan du finde seneste produkt opdateringer/montagevejledninger samt support tlf. nr/mail. www.lindab.dk…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.