Инструкция на Контроллеры Lennox серии CLIMATIC 10, 40

Текст инструкции

1. Стр. 1 OPERATING AND INSTALLATION

2. Стр. 2 TABLE OF CONTENTS

   CONTENTS PAGE • GENERAL DESCRIPTION • TERMINAL-THERMOSTAT INSTALLATION • USER INTERFACE DESCRIPTION • SELECTING UNIT OPERATING MODE AND SET-POINT • SELECTING THE TEMPERATURE SET-POINT CATEGORY • CLOCK AND TIME BANDS (AS AN OPTION) • PARAMETERS, STATUS AND READINGS (PROGRAMMING) • DEFROST MANAGEMENT…

3. Стр. 3 GENERAL DESCRIPTION

   This electronic control is organised into two integrated systems: a terminal, installed in the room, and a power board for managing the actuators in the electrical panel. The terminal is connected to the power board using a two-lead cable, thus greatly simplifying installation. AIR CONDITIONING UNIT…

4. Стр. 4 TERMINAL-THERMOSTAT INSTALLATION

   For correct installation the following warnings must be heeded: • Always disconnect the power supply before performing any operations on the board during assembly, maintenance or replacement. • The terminal should be fastened to the wall vertically, allowing for air to circulate through the…

5. Стр. 5 USER INTERFACE DESCRIPTION

   THE CONTROL IS ACTIVE 5 SECONDS AFTER THE UNIT POWER IS SWITCHED ON FUNCTIONS OF THE BUTTONS AND BUTTONS These are placed on the front panel of the instrument. These allow the immediate setting of the desired temperature (set-point), and with them the parameters could be modified. While unit is ON…

6. Стр. 6 SELECTING UNIT OPERATTING MODE AND SET-POINT TEMPERATURE

   A ) SELECTING THE UNIT'S OPERATING MODE clock set mode fan hold resume The operating mode is always indicated on the display Pressing the mode button repeatedly you can change the unit operating mode COOL: The unit is working on cooling mode, when compressor is working symbol will appear on the…

7. Стр. 7 SELECTING THE TEMPERATURE SET POINT CATEGORY

   SELECTING THE TEMPERATURE SET POINT CATEGORY After COOL, HEAT or AUTO, operating mode have been selected, pressing set button select the set point category. There are 3 possible set-point categories available 1- Comfort set-point (indicated by the symbol ): Is the reference room desired temperature…

8. Стр. 8 CLOCK AND TIME BANDS (AS AN OPTION)

   This electronic control with clock fuction, is a programmable terminal (programming the time bands). With this terminal set-point desired can be set for 24 hours a day, seven days a week. This programable operation is optional, and must be specified at the time of order. Proceed as follow to program…

9. Стр. 9 CLOCK AND TIME BANDS PROGRAMMING

   PROGRAMMING PROCESS clock set mode Mo Tu We Th Fr Sa Su clock fan Mo Tu We Th Fr Sa Su hold 1 resume set mode 2 fan hold To set a program, Press clock for 5 seconds, t1 will show on the display resume clock set Mo mode 3 Mo (Monday) Tu (Tuesday) We (Wednesday) Th (Thursday) Fr (Friday) Sa (Saturday)…

10. Стр. 10 CLOCK AND TIME BANDS PROGRAMMING

    After all time bands have been programed and unit it is working on any of them, there are two ways to change the desired set-point for the time-band currently in use: A) Change the desired set-point of the current time-band for three hours. The desired set-point can be changed, using the and…

11. Стр. 11 PROGRAMMING THE PARAMETERS

    All modifications on the operating unit parameters, must be carried out by qualified personnel. Incorrect programming of the parameters may cause damage to the unit. And consecuently the loss of guarantee of the unit. Procced as follow, to reach to the operating parameters of the unit: Step 1 Step 2…

12. Стр. 12 PROGRAMMING

    The table below gives the following information for each parameter. COD: The code which appears on the display The field variation for the parameters, MIN: Maximum value for the parameter MAX:Minimum value for the parameter UNIT: The units of measure used. C=Centigrade, F=Fahrenheit, s= seconds…

13. Стр. 13 PROGRAMMING

    VALUES DESCRIPTION COD MIN MAX UNIT VAR. DEF C5 Hour-counter compressor. Indicates the number of compressor operating hours. When 19.900 working hours have been reached, the parameter starts counting again . 0 19,9 Khrs F3 Hour-counter inner fan. Indicates the number of inner fan operating hours.…

14. Стр. 14 DEFROST MANAGEMENT

    The defrost process is activated during heating mode in heat pump units, when the outside temperature is low and the outdoor coil could become frozen. To melt the ice the defrost function will switch the unit to cooling operation for a short period. Note: During defrost function, if indoor fan is…

15. Стр. 15 ALARM CODES

    The unit self-protect through safety devices, whn any of these safety devices detect an anomaly, shown in the display in order to advice the installer. The activation of an alarm brings about: - The display of the alarm code and the letters "AL", alternating with the display of the temperature - The…

16. Стр. 16 REMOTE SENSORS (AS AN OPTION)

    As an option, there are available two types of remote sensors: - REMOTE DUCT SENSOR: The sensor should be located at the return air duct , recording the room temperature continously. - REMOTE AMBIENT SENSOR: The sensor should be located at the room which has to be conditioned Both should be used…

17. Стр. 17 POWER BOARD OF THE SYSTEM AT THE ELECTRICAL BOX OF THE AIR-CONDITIONING UNIT

    Power supply: 24V ac+10%-15% 50/60Hz - The board features a signalling green LED which flashes when unit is electrically supplied. - The centre of the board also houses a jumper J3, which must be setted on the position showed in the electrical diagram supplied with the unit (between ID COM and INT).…

18. Стр. 18 POINTS TO KEEP IN MIND

    Standard Guidelines to Lennox Refac equipment All technical data contained in these operating instructions including the diagrams and technical description remains the property of Lennox Refac and may not be used (except for the purpose of familiarising the user with the equipment), reproduced…

19. Стр. 20 GREAT BRITAIN,

    IRELAND: LENNOX INDUSTRIES LTD tél. : + 44 1604 59 9400 fax : + 44 1604 594200 e-mail : marketing lennoxind.com BELGIUM : LENNOX BENELUX N.V./S.A. tél. : + fax : + e-mail : inf.beo lennoxbenelux.com CZECH REPUBLIC : JANKA RADOTIN AS tél. : + fax : + e-mail : janka janka.cz FRANCE : LENNOX FRANCE…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.