Инструкция на Контроллеры Lennox серии CLIMATIC 50, 60, 200 / 400

Текст инструкции

1. Стр. 1 User manual

   CLIMATIC™ 200/400 - Controller Providing indoor climate comfort MUL35E-0506 09-2006

2. Стр. 3 GENERAL DESCRIPTION

   This equipment is an electronic device that controls packaged water cooling systems via air and reversible air/water heat pumps: (EAC/EAR 0251SM to 1804SM). The thermostat allows the following operations: - Unit ON/OFF. - Select system operating mode. - Set point adjustment. - Alarm signal relay.…

3. Стр. 4 THE KEYPAD INCORPORATED AT THE UNIT, MODEL Climatic® 200

   READING DISPLAY This is a 3-digit display, the inlet water temperature is shown in degrees (default), ºC (when shows decimal point). The following can also be displayed: - Values of all parameters controlled by the equipment. - Cooling set point, cooling differential temperature. - Heating set point…

4. Стр. 5 THE KEYPAD INCORPORATED AT THE UNIT, MODEL Climatic® 400

   READING DISPLAY This is a 3-digit display, the inlet water temperature is shown in degrees (default), ºC (when shows decimal point). The following can also be displayed: - Values of all parameters controlled by the equipment. - Cooling set point, cooling differential temperature. - Heating set point…

5. Стр. 6 THE KEYPAD REMOTE CONTROLLER (OPTION), MODEL RC Climatic® 200

   READING DISPLAY This is a 3-digit display, the inlet water temperature is shown in degrees (default), ºC (when shows decimal point). The following can also be displayed: - Values of all parameters controlled by the equipment. - Cooling set point, cooling differential temperature. - Heating set point…

6. Стр. 7 THE KEYPAD REMOTE CONTROLLER (OPTION), MODEL RC Climatic® 400

   READING DISPLAY This is a 3-digit display, the inlet water temperature is shown in degrees (default), ºC (when shows decimal point). The following can also be displayed: - Values of all parameters controlled by the equipment. - Cooling set point, cooling differential temperature. - Heating set point…

7. Стр. 8 FUNCTION

   UNIT COMMISSIONING When all the instructions in the Operating, Service and Installation Manual have been carried out, the unit can be commissioned as follows: POWER SUPPLY TO THE UNIT - Set the general cut-off switch to ON. TURN ON/OFF THE UNIT - Pressing on off button for more than 2 seconds lets…

8. Стр. 9 MENU MODE

   Press mode and on off buttons and release within 2 seconds, to enable the user to get to the menu mode mode To move through the menu on this way : Press mode and on off buttons simultaneously and release within 2 seconds. To move through the menu on this way : Press mode and on off buttons…

9. Стр. 10 SET POINT THERMOSTAT FUNCTION DESCRIPTION

   LEVEL 1 MAIN DISPLAY It shows: Inlet water temperature Active alarms LEVEL 2 SET POINT LEVEL 3 Cooling set point Set point value Heating set point Set point value See page 7, for adjustment of set point of the system. The water temperature is thermostatically controlled via a set point and a…

10. Стр. 11 ANALOGUE INPUTS

    MAIN DISPLAY It shows: Inlet water temperature Active alarms SET POINT mode Press Probe value Press Probe value on off Probe status Probe value Probe value Probe value mode mode + + on off on off >2" <2" NOTE: When the leds on the display flash alternatively from one to the other, you are on menu…

11. Стр. 12 OPTIONS

    ON/OFF REMOTE Remove the wire between 93 and 94 terminal block on the electrical box and insert a contact. If the unit stops with ON/OFF Remote, "E00" will appear on the unit display. REMOTE CHANGEOVER SUMMER/WINTER On heat pump units, it is possible to select cooling or heating mode with a remote…

12. Стр. 13 OPTIONS

    Set point ºC Set point ºC DYNAMIC SET POINT 42ºC heating set point 12ºC 38ºC 9ºC cooling set point 25ºC 35ºC starting differential Dynamic set point -10ºC outdoor temp. ºC outdoor temp. ºC 6ºC starting differential Dynamic set point 6ºC COOLING MODE When the outdoor temperature exceeds 35ºC, the…

13. Стр. 14 MODIFY PARAMETERS

    MAIN DISPLAY Press mode on off It shows: Inlet water temperature Active alarms Press Press Press Press mode on off PARAMETERS mode mode + + on off on off >2" <2" NOTE: When the leds on the display flash alternatively from one to the other, you are on menu mode. Menu of configuration parameters of…

14. Стр. 15 MODIFY UNIT PARAMETERS

    MAX: Maximum value for the parameter. MIN: Minimum value for the parameter. DEF: The default value, factory set. UNIT: The units of measure used. VAR.: Minimum variation allowed. DESCRIPTION MIN MAX DEF UNIT VAR. 1 CIRCUIT UNIT MODEL Climatic® 200 Cooling thermal regulator hysteresis Heating thermal…

15. Стр. 16 OPERATING HOURS

    mode Press on off It shows: Inlet water temperature Active alarms Press Press Press Press Compressor 1 operating hours Compressor 2 operating hours mode Press Press Compressor 3 operating hours on off Compressor 4 operating hours OPERATING HOURS Water pump operating hours mode mode + + on off on off…

16. Стр. 17 MENU STRUCTURE

    MAIN DISPLAY It shows: Inlet water temperature Active alarms LEVEL 1 SET POINT Press Probe status mode Press Press LEVEL 2 on off Active alarms Codes ALARMS The unit self-protects through safety devices; when any of these safety devices detect an anomaly, this is shown in the display in order to…

17. Стр. 18 VIS

    DESCRIPTION E05 Anti-freeze alarm. It indicates the outlet water temperature is lower than +3ºC (it kit low water temperature is not fitted). After 1 automatic reset, it comes to be a manual reset. E06 Outlet water temperature probe alarm (St2). Outlet water temperature probe open or without…

18. Стр. 19 VIS

    DESCRIPTION E23 Compressor 1 circuit 2 thermal protection alarm: Compressor 1 - Compressor thermal protection open. circuit 2 MAN - Faulty power supply. stops E24 Fan thermal protection alarm. EFFECT Circuit 2 fan and circuit 2 compressors stop RE ACTION Check: • Check refrigerant charge. • Check…

19. Стр. 20 DESCRIPTION OF THE DEFROSTING SYSTEM

    The defrosting process is activated during heating mode in heat pump units, when the outside temperature is low and the outdoor coil could become frozen. To melt the ice the defrosting function will switch the unit to cooling operation for a short period. During defrosting mode the low pressure is…

20. Стр. 21 FAN SPEED CONTROL (only for 0091 to 0812 units)

    Fan speed control: Management of the fan speed It is managed by a fan speed control printed plate located at the electrical box of the unit. The function of the fan speed control is to prevent very low condensing temperatures during cooling mode operation between 0ºC and 46ºC outside temperatures.…

21. Стр. 22 SAFETY DEVICES

    The units contain various safety devices to avoid damage to the unit due to very low water temperatures. 1.- Anti-freeze protection. This protection is activated by the control of the unit when the outlet water temperature probe (St2), located inside the water exchanger, measures +5ºC and…

22. Стр. 24 www.lennoxeurope.com

    BELGIUM, LUXEMBOURG www.lennoxbelgium.com PORTUGAL www.lennoxportugal.com Due to Lennox’s ongoing commitment to quality, the Specifications, Ratings and Dimensions are subject to change without notice and without incurring liability. CZECH REPUBLIC www.lennox.cz RUSSIA www.lennoxrussia.com Improper…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.