Инструкция на Бустерные насосы Hayward 6060

Текст инструкции

1. Стр. 1 P/N: IS6060

   Rev: B OWNER’S MANUAL INSTALLATION, OPERATION, & PARTS 6060 Booster Pump The Hayward 6060 booster pump is specifically engineered for the demanding requirements of today’s in-ground swimming pool cleaning systems. The 6060 booster pump includes an improved seal and impeller design that will provide…

2. Стр. 2 _____________________________ Page 2 of 16

   IMPORTANT SAFETY INSTRUCTIONS Before installing or servicing this electrical equipment, turn power supply OFF. Basic safety precautions should always be followed, including the following: Failure to follow instructions may result in injury. This is the safety-alert symbol. When you see this symbol…

3. Стр. 3 _____________________________ Page 3 of 16

   WARNING –Risk of Electric Shock. All electrical wiring MUST be in conformance with all applicable local codes, regulations, and the National Electric Code (NEC). Hazardous voltage can shock, burn, and cause death or serious property damage. To reduce the risk of electric shock, do NOT use an…

4. Стр. 4 _____________________________ Page 4 of 16

   WARNING – Hazardous Pressure. Pool and spa water circulation systems operate under hazardous pressure during start-up, normal operation, and after pump shut-off. Stand clear of circulation system equipment during pump start-up. Failure to follow safety and operation instructions could result in…

5. Стр. 5 _____________________________ Page 5 of 16

   Product Specifications Installation Instructions WARNING – This product should be installed and serviced only by a qualified professional. Pump Location Pressure Cleaner Locate booster pump as shown in above diagram and run suction lines as direct as possible to reduce friction loss. Suction lines…

6. Стр. 6 _____________________________ Page 6 of 16

   WARNING – Hazardous Pressure. Pumps, filters, and other equipment/ components of a swimming pool filtration system operate under pressure. Incorrectly installed filtration equipment and/or components may fail resulting in severe personal injury or death. Plumbing It is recommended to use the…

7. Стр. 7 _____________________________ Page 7 of 16

   Electrical WARNING – All electrical wiring MUST be in conformance with all applicable local codes, regulations, and the National Electric Code (NEC). Ground and bond motor before connecting to electrical power supply. Failure to ground and bond pump motor can cause serious or fatal electrical shock…

8. Стр. 8 _____________________________ Page 8 of 16

   Start-Up & Operation Prior to Start-Up WARNING – All suction and discharge valves MUST be OPEN, as well as filter manual air relief valve (if available) on filter, when starting the circulating pump system for the first time, or after servicing the system. Failure to do so could result in severe…

9. Стр. 9 _____________________________ Page 9 of 16

   Maintenance Hayward pumps have self-lubricating motor bearings and shaft seals. No lubrication is necessary. Keep motor clean. Insure motor air vents are free from obstruction to avoid damage. Do NOT use water to hose off motor. Occasionally, shaft seals must be replaced, due to wear or damage.…

10. Стр. 10 _____________________________ Page 10 of 16

    Shaft Seal Change Instructions (cont’d.) Removing the Motor Assembly (See Parts Diagram on page 11 of this manual for pump component locations.) 1. 2. Remove the eight (8) 1/4" x 1-1/4" self-tapping screws (item #1), which hold the volute (item #2) to the seal plate (item #7), using a Phillips head…

11. Стр. 11 _____________________________ Page 11 of 16

    Replacement Parts Parts Diagram Optional Hose Kit 6060HKIT Parts Listing Ref. No. Part No. Description Ctn. Qty. 1 AX6060Z1 Screw, ¼” Type B x 1-¼” (set of 10) 10 2 AX6060A 1 3 AX6060UNPAK 4 AX6060C Pump Volute Union Connector Kit (incl. 2 ea. Union Hose Connector, Union Pipe Connector, Union Nut…

12. Стр. 12 _____________________________ Page 12 of 16

    Troubleshooting Motor Will NOT Start – Check For: Make sure the terminal board connections agree with the wiring diagram on motor data plate label. Be sure motor is wired for available field supply voltage (see pump operating label). 1. Improper or loose wiring connections; open switches or relays…

13. Стр. 13 _____________________________ Page 13 of 16

    PRODUCT REGISTRATION (Retain For Your Records) DATE OF INSTALLATION: INITIAL PRESSURE GAUGE READING (CLEAN FILTER): BOOSTER PUMP MODEL: 6060 HORSEPOWER: FILTER MODEL: WWW.HAYWARDPOOL.COM 0.75 FRHP (1.25 THP) BOOSTER PUMP SERIAL NO.: USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

14. Стр. 14 _____________________________ Page 14 of 16

    THIS PAGE IS BLANK WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

15. Стр. 15 _____________________________ Page 15 of 16

    HAYWARD® LIMITED WARRANTY This pump was inspected before shipment from our plant. To original purchasers of this pump, Hayward Pool Products, 620 Division Street, Elizabeth, New Jersey, warrants its products free from defects in materials and workmanship for a period of ONE (1) year from the date of…

16. Стр. 16 _____________________________ Page 16 of 16

    THIS PAGE IS BLANK WWW.HAYWARDPOOL.COM USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.