Инструкция на Тепловые насосы для бассейна Hayward серии HeatPro - HP50TA

Текст инструкции

1. Стр. 1 Owner’s Manual

   PRINTED IN CANADA 10/2009 13024800 Rev C

2. Стр. 3 Table of contents

   Introduction 2 General Safety Instructions 4 Installation Instructions Location 6 Water piping 7 Electrical 7 Bonding 8 Bonding and plumbing step-by-step instructions 8 Installation in Combination with Solar or Gas Heaters 10 Using an External Controller 11 Electrical Connections 12 Wiring Diagram…

3. Стр. 4 Thank you for buying

   a HAYWARD pool heat pump. The HAYWARD pool heat pump is a self-contained unit designed specifically for pool heating. Each component has been selected with care to achieve a high-quality product in an effort to exceed all industry standards. All HAYWARD pool heat pumps have an electronic board with…

4. Стр. 5 Please read carefully

   Record your model’s information Please complete and mail in the ownership registration card provided with this guide. The return address is displayed on the front of your registration card. Simply mail it as you would a postcard. The card helps us notify you about any new information about your…

5. Стр. 6 General Safety Instructions

   We care for our customers We have provided important safety messages in this manual and on your heater. Always read and obey all safety messages. ? IMPORTANT The IMPORTANT sign calls attention to a note that provides important information or information essential to the completion of a task. CAUTION…

6. Стр. 7 CAUTION

   ! ! All electrical connections must be done by a qualified electrician and according to the local electrical codes. Always cut off the unit’s main power whenever the access panel is open or removed. Always install the machine outdoors (unless otherwise approved by the manufacturer), while respecting…

7. Стр. 8 Installation Instructions

   ATTENTION!!! CONSUMER KIT LOCATED BEHIND FRONT PANEL Location The placement of the pool heater is very important in keeping installation costs to a minimum while providing for maximum efficiency of operation, as well as allowing adequate access for service and maintenance. The pool heat pump is…

8. Стр. 9 Water piping

   ? IMPORTANT The piping sequence is as follows: pool > pool pump > filter > heater > check valve > chemical feeder > pool. Automated chlorine distribution systems, if used, must be placed downstream of the heater to minimize harm to the pool equipment. Use rigid PVC piping if possible (SCH40 or…

9. Стр. 10 Bonding

   ! CAUTION Because all metals have different electrical potentials, all metal and electrical components of the pool system must be bonded together. This includes the metal framework of the pool, the light, the pump, the filter (if made out of metal), the heater, any automatic chlorine generator, and…

10. Стр. 11 Bonding and Plumbing diagram

    Fig. 2 Chemical feeder Heat Pump Fig. 3 Owner’s manual 9

11. Стр. 12 Installation in Combination with

    Solar or Gas Heaters If you are installing a heat pump in combination with any other type of heating device, please call the HAYWARD service department at (908) 355-7995. We will advise you of installation practices that will help keep your warranty valid. Other pool heaters, such as gas-fired or…

12. Стр. 13 Using an External Controller

    To connect the electronic board in order to control it remotely, use the P_S terminals on the right side of the board. Next, access the P_S menu and select the desired mode. In internal mode, POOL or SPA mode can be adjusted by using this menu. In external mode, a normally open contact puts the…

13. Стр. 14 Electrical Connections

    WARNING The installation of the pool heater should be performed by a certified electrician. To connect the electricity, you must unscrew the five screws of the front panel, then slide the electric cable through the knock out located on the left or the right side of the base, and then insert it in…

14. Стр. 15 Owner’s manual

    Flow switch Closed = flow Opened = no flow Low pressure switch Closed = OK Opened = low pressure High pressure switch Closed = OK Opened = high pressure Defrost sensor Water sensor LP LP FLO FLO HGD H/C Black 24 VAC Yellow P S Yellow Yellow FAN Light Blue Purple Purple Light Blue 24 Vac R S 1 Phase…

15. Стр. 16 Service Analyzer Control

    The control panel is factory set to display the temperature in Fahrenheit degrees. Celsius or Fahrenheit mode Heating mode Compressor ( ) or fan ( ) running Temperature and parameter display Heating mode To raise the desired temperature or to change parameters Access to parameters To lower the…

16. Стр. 17 Operation

    To increase the temperature Push the SET key until you see POL or SPA. The programmed temperature will be displayed. Press the UP arrow to increase the temperature setting one degree at a time. To lower the temperature Proceed as explained above using the down arrow . To select the pool or spa mode…

17. Стр. 18 Caring for your Pool Heater

    How to protect your pool heater 16 Owner’s manual

18. Стр. 19 Initial Startup

    ? IMPORTANT Before starting the pool heater for the first time, it is important to verify that the breaker is in the ON position. Also make sure that the water circulates freely and that the pool pump is activited. Then, you will need to set the water temperature you desire. The fan will immediately…

19. Стр. 20 Meaning of Display Codes

    Service Analyzer Codes Most problems will be detected by the service analyzer and a code will be displayed on the digital display of your heater. Display Meaning of codes OFF The desired programmed temperature point is lower than 60°F (15°C). LP & LP3 Shortage of refrigerant gas in the unit or…

20. Стр. 21 Troubleshooting

    The pool heater is not running. Heat pump control set to OFF. Raise temperature set point above 60°F (15°C). Desired water temperature is reached. Unit will automatically restart when the water temperature goes below the set point. Main breaker is tripped. Reset main breaker and restart heat pump.…

21. Стр. 22 There is no display and the fan is not running,

    but the compressor is running. Ask your electrician to verify your heat pump’s power supply by checking over the L1 and L2 connections in the unit’s service box. There is water around the unit. While your pool heater is in the heating mode, a large quantity of warm and humid air passes over the…

22. Стр. 23 Requesting Assistance or Service

    ? IMPORTANT All service will be handled by an Authorized Service Center. Warranty may be voided if service is not done by an Authorized Service Representative. Do not return the heater to your dealer as they do not provide service. Before calling for assistance or service, please check the…

23. Стр. 24 Maintenance

    Dirt can accumulate on the evaporator. You can easily remove it by using a non-pressured water spray without damaging the small aluminum fins. The cleaning of the plastic cabinet can be done with the help of a brush and soap. Winterizing First, you must turn the breaker off. The unit must be drained…

24. Стр. 25 Hayward® Heat Pump Pool Heater

    Limited Warranty The HAYWARD heat pump pool heater is warranted to be free of defects in materials and workmanship for a period of two (2) years for parts and (1) one year for labor. In the state of Florida, warranty labor is covered for (2) years. This warranty is applicable to the original…

25. Стр. 26 International Warranty

    The HAYWARD heat pump pool heater is warranted to be free of defects in materials and workmanship for a period of one (1) year. The compressor is warranted for two (2) years, and the titanium tube component of the heat exchanger has a ten (10) year warranty. The above coverage begins from the date…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.