Инструкция на Насосы для бассейнов с префильтром Hayward серии PowerFlo LX/ PowerFlo II / EP

Текст инструкции

1. Стр. 2 WAR

   RNING - Rea ad and follo ow all instrructions in tthis owner’s manual and oon the equipment. Failuree to follow instructions can cause se evere injury and/or death.. WAR RNING – Sucction Entrapm ment Hazard. Suction in suction s outlets and/or suction n outlet covers which w are, dam maged, broken…

2. Стр. 3

   WARNING – Separation Hazard. Failure to follow safety and operation instructions could result in violent separation of pump and/or filter components. Strainer cover must be properly secured to pump housing with strainer cover lock ring. Before servicing pool and spa circulation system, filters…

3. Стр. 4 Installation Instructions

   Pump Location The PowerFlo LX™ and EP series pumps MUST be installed below the pool water line (see Figure to right). Self-priming PowerFlo II™ pumps may be installed up to four (4) feet above the pool water line. Install pump on a firm, level base or pad to meet all local and national codes. The…

4. Стр. 5 Fittings

   Fittings restrict flow. For better efficiency, use the fewest possible fittings. Avoid fittings that could cause an air trap. Electrical WARNING – Ground motor before connecting to electrical power supply. Failure to ground pump motor can cause serious or fatal electrical shock hazard. WARNING – Do…

5. Стр. 6 New Installation – Start-Up & Operation

   Prior to Start-Up Fill strainer housing with water to suction pipe level. NEVER operate the pump without water. Water acts as a coolant and lubricant for the mechanical shaft seal. WARNING – NEVER run pump dry. Running pump dry may damage seals, causing leakage and flooding. Fill strainer housing…

6. Стр. 7 Start-Up for Winterized Equipment

   1. Follow filter manufacturer's instructions for reactivation of the filter. 2. Inspect all electrical wiring for damage or deterioration over the shutdown period. Have a qualified serviceman repair/replace wiring as needed. 3. Securely mount pump to base. 4. Install all intake and output fittings…

7. Стр. 8 Troubleshooting

   Motor Will NOT Start – Check For: 1. Improper or loose wiring connections; open switches or relays; tripped circuit breakers, GFCI’s, or blown fuses. 2. Manually check rotation of motor shaft for free movement and lack of obstruction. (See steps 4 & 5 of “Shaft Seal Change Instructions” in this…

8. Стр. 9 Noisy Pump – Check For

   1. Air leak in suction piping causing rumbling in pump. 2. Cavitation due to restricted or undersized suction line or leak at any joint, low water level in pool, and unrestricted discharge return lines. Correct suction condition or throttle return lines, if practical. Holding hand over return…

9. Стр. 10 Replacement Parts

10. Стр. 11 HAYWARD® Pool Products Limited Warranty

    To original purchasers of this equipment, Hayward Pool Products, Inc. warrants its products to be free from defects in materials and workmanship for a period of ONE (1) year from the date of purchase, when used in single family residential applications. The limited warranty excludes damage from…

11. Стр. 12 DETACH HERE: Fill out bottom

    b portion completely c and mail within 10 d ays of purchasee/installation or register online. Po owerFlo LX™ / Pow werFlo II™ ™ / EP Pum mp Seriess Wa arranty C Card Reg gistration n Register online at www.haayward.com Plea ase Print Clea arly: Yeaars Pool has been n in service 4-5 6-10 1-3 11-15…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.