Инструкция на Насосы для бассейнов с префильтром Hayward серии Super Pump

Текст инструкции

1. Стр. 2 WARN

   NING – Read d, understa and, and fo ollow all insstructions in this owner’ss manual and oon the eq quipment. Failure to follow instructions ca an cause severre injury and/o or death. WARN NING – Suction Entrapmeent Hazard. Suction in suction s outlets and/or suction n outlet covers which w are, dam…

2. Стр. 3

   WARNING – Risk of Electric Shock. All electrical wiring MUST be in conformance with applicable local codes, regulations, and the National Electric Code (NEC). Hazardous voltage can shock, burn, and cause death or serious property damage. To reduce the risk of electric shock, do NOT use an extension…

3. Стр. 4 General Information

   Introduction This manual contains information for the proper installation and operation of the Hayward Super Pump® Series. The instructions in this manual MUST be followed precisely. Failure to install according to defined instructions will void warranty. Product Benefits         Super-sized…

4. Стр. 5 Pump Mounting

   Install pump on a firm, level base or pad to meet all local and national codes. Fasten pump to base or pad with screws or bolts to reduce vibration and stress on pipe or hose joints. The base MUST be solid, level, rigid, and vibration free. Pump mount must:  Allow pump inlet height to be as close…

5. Стр. 6 Use copper conductors only

   MOTOR KW HP .37 1/2 .55 3/4 .75 1 1.1 1-1/2 1.55 2 1.88 2-1/2 ELECTRICAL GUIDE – 60 CYCLE MOTORS – SINGLE PHASE CIRCUIT BREAKER BRANCH FUSETRON VOLTS RATINGS-AMPS RATINGS-AMPS 6.25 RECOMMENDED WIRE SIZE 0-50’ No. 14 No. 14 No. 14 No. 12 No. 14 No. 10 No. 14 No. 10 No. 14 No. 12 Voltage Voltage at…

6. Стр. 7

   NOTICE – NEVER OPERATE THE PUMP WITHOUT WATER. Water acts as a coolant and lubricant for the mechanical shaft seal. NEVER run pump dry. Running pump dry may damage seals, causing leakage, flooding, and voids warranty. Fill strainer housing with water before starting motor. NOTICE – Do NOT add…

7. Стр. 8 Shaft Seal Change Instructions

   IMPORTANT SAFETY INSTRUCTIONS PLEASE READ AND FOLLOW ALL INSTRUCTIONS WARNING – Electrical Hazard - Failure to disconnect power may result in serious personal injury or death. To avoid, turn OFF power to motor before servicing pump. NOTICE- Only qualified personnel should attempt rotary seal…

8. Стр. 9 Replacement Parts

9. Стр. 10 Troubleshooting

   Motor Will NOT Start – Check For: Make sure the terminal board connections agree with the wiring diagram on motor data plate label. Be sure motor is wired for available field supply voltage. 1. Improper or loose wiring connections; open switches or relays; tripped circuit breakers, GFCI’s, or blown…

10. Стр. 11 Low Flow – Generally, Check For

    1. Clogged or restricted strainer or suction line. Solution: Contact a qualified repair professional. 2. Undersized pool piping. Solution: Correct piping size. 3. Plugged or restricted discharge line of filter, valve partially closed (high gauge reading). Solution: Sand filters – backwash as per…

11. Стр. 12 DETACH HERE

    H Fill out bottom portion com mpletely and mail within 10 days of purchase/insstallation or reg gister online. Su uper Pum mp® Serie es Wa arranty C Card Registration n Register R onlin ne at www.haayward.com Plea ase Print Clearrly: Yearrs Pool has been in service 4-5 6-10 1-3 11-15 >15 Firs t…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.