Инструкция на Насосы для бассейнов с регулируемой скоростью Hayward серии MaxFlo VS SP23520VSP

Текст инструкции

1. Стр. 1

   MaxFlo VS™ 500 Owner’s Manual Model SP23520VSP MaxFlo VS 500 Variable Speed Pump Hayward’s MaxFlo VS 500 variable speed pump delivers incredible energy savings via its advanced hydraulic design combined with a totally enclosed, permanent magnet motor. MaxFlo VS 500 is easily installed either as a…

2. Стр. 4 1. IMPORTANT SAFETY INSTRUCTIONS

   Before installing or servicing this electrical equipment, turn power supply OFF. Basic safety precautions should always be followed, including the following: Failure to follow instructions may result in injury. This is the safety-alert symbol. When you see this symbol on your pump or in this manual…

3. Стр. 5

   WARNING – Pool and spa components (seals, gaskets, etc.) have a finite life. All components should be inspected frequently and replaced at least every ten years, or if found to be damaged, broken, cracked, missing, or not securely attached. WARNING – Risk of Electric Shock. All electrical wiring…

4. Стр. 6 WARNING – To Reduce the risk of Entrapment Hazards

    When outlets are small enough to be blocked by a person, a minimum of two functioning suction outlets per pump must be installed. Suction outlets in the same plane (i.e. floor or wall), must be installed a minimum of three feet (3’) [0.91 meter] apart, as measured from near point to near point. …

5. Стр. 7 2. General Information

   2.1. Introduction This manual contains information for the proper installation and operation of the Hayward MaxFlo VS 500 Variable Speed Pump. The instructions in this manual MUST be followed precisely. 2.2. Primary Features       Totally enclosed, permanent magnet motor Advanced hydraulic…

6. Стр. 8 3. Energy Efficiency Overview

   The energy consumed by a pool pump is measured in terms of Watts (W) or Kilowatts (kW). The MaxFlo VS 500 Variable Speed Pump displays power consumption in Watts. Given this information, you can determine the cost of operating the pump: Power consumption of pump X Cost of electricity = Cost of Pump…

7. Стр. 9 4.2. Pump Mounting

   Install pump on a level concrete slab or other rigid base to meet all local and national codes. Secure pump to base with screws or bolts to further reduce vibration and stress on pipe or hose joints. The base must be level, rigid, and vibration free. Pump mount must:  Allow pump inlet height to be…

8. Стр. 10 4.5. Electrical

   WARNING – All electrical wiring MUST conform to local codes, regulations, and the National Electric Code (NEC). WARNING – Ground and bond pump before connecting to electrical power supply. Failure to ground and bond pump can cause serious or fatal electrical shock hazard. Do NOT ground to a gas…

9. Стр. 11 4.10. Remote Control Wiring/Operation

   MaxFlo VS 500 can be controlled in a wide variety of ways as described below: 1. MaxFlo VS 500 can operate by itself in Stand-Alone Mode using its built-in programmable timers. 2. MaxFlo VS 500 can also be controlled from third party controls (i.e. another manufacturer’s control) and Hayward…

10. Стр. 12 4.12. Interface Wall Mounting

    The interface can also be wall mounted using the parts supplied in the optional wall mount kit using the following procedure. 1. TURN OFF THE ELECTRICAL POWER AT THE CIRCUIT BREAKER. 2. Loosen the two screws securing the user interface to the motor drive and remove the user interface. (Figure…

11. Стр. 13 Fig

    gure 4.12-2: Re emoving the Interface Mou unting Plate to o access the D Drive wiring co ompartment A the Bllank Cover Figure 4.12-3: Adding Page e 13 of 36 H GENUINE G REPLACEMENTT PARTS USE ONLY HAYWARD MaxFlo o VS 500 Pu ump IS23520V VSP Rev-D

12. Стр. 14 Figure 4.12-4: Wall Mounting the Interface

    4.13. Installation Procedure Please review sections 4.1 through 4.12 before continuing with this section. 1. TURN OFF THE ELECTRICAL POWER AT THE CIRCUIT BREAKER AND REMOVE THE USER INTERFACE. 2. Loosen the two screws securing the user interface to the motor drive and remove the user interface. …

13. Стр. 15 5. Wiring Diagrams

    5.1. Input Power Wiring (Required) Figure 5.1-1 DRIVE HIGH VOLTAGE CONNECTIONS 5.2. Wall Mounted Digital Control Interface Wiring (Optional) Figure 5.2-1 Connection wire must be rated for a minimum of 300V, and may be up to 500 feet in length. Use removable 4-position terminal block connectors for…

14. Стр. 16 5.3. External Relay Speed Control Wiring (Optional, for remote selection of pump

    speed) Note: For third party controls and Hayward controls that are NOT software compatible. Figure 5.3-1 Connection wire must be rated for a minimum of 300V. Inputs are rated to accept a low voltage supply of 18-30VAC (24VAC+/-20%) or 9-30VDC (12/24VDC +/-20%). The “+12V” and “COM” terminals may be…

15. Стр. 17 5.4. Hayward Automation Control Wiring (Optional, for remote control of pump

    speed) Note: For software compatible Hayward controls only. Existing user interface wiring connection (if present) should be unplugged and second terminal block connector should be used to make wiring connections shown below. Figure 5.4 1 The MaxFlo VS 500 pump can communicate with and be controlled…

16. Стр. 18 5.5. Remote Stop Switch Wiring (Optional)

    Figure 5.5-1 Connection wire must be rated for a minimum of 300V. Switch must be latching type; pump is stopped when circuit is closed. Inputs are rated to accept a low voltage supply of 18-30VAC (24VAC +/-20%) or 9-30VDC (12/24VDC +/-20%). The “+12V” and “COM” terminals may be used as a low voltage…

17. Стр. 19 6.2. Starting/Priming the Pump

    Refer to item #9 in section 6.6 for priming time selection. Fill strainer housing with water to suction pipe level. If water leakage occurs from anywhere on the pump or filter, DO NOT start the pump. If no leakage occurs, stand at least 10 feet from pump and/or filter and proceed with starting the…

18. Стр. 20 6.3. User Interface Summary

    Figure 6.3-1 1. Preset Speeds: Buttons labeled SPEED 1 thru SPEED 4 can be used to run the pump at a predetermined speed for a certain length of time. Preset Speed settings can be quickly updated using the + and - arrow buttons to change the speed and then pressing the > button to save the new speed…

19. Стр. 21 6.4. Menu Outline

    1. Configuration Menu (see section 6.6 for basic product configuration) a. Set Day and Time b. Speed Selection c. MAX Allowed Speed d. MIN Allowed Speed e. Prime Duration f. Remote Control Mode g. Low Temp Operation h. Low Temp Setting 2. Timer Menu (see section 6.7 to program the 8 speeds with…

20. Стр. 22 6.6. Configuration Menu

    Screen 1. Configuration Menu Locked 2. Configuration Menu press > to enter 3. Use + / - to adjust, > go to next item 4. Time: Th 1:27PM + change or > skip 5. Set Day and Time Thursday 1:27p 6. Speed Selection rpm 7. MAX allowed speed 3450 (600-3450rpm) 8. MIN allowed speed 600 (600-3450rpm) 9. Prime…

21. Стр. 23

    pump, system plumbing, or pool from freezing. If Low Temp Operation is disabled, the temperature setting screen is not shown. Buttons Used Screen Comments 13. Reset all parameters + for yes; > to skip +<> Use + to reset to factory default settings Use > to skip reset 14. Are you sure? + for yes…

22. Стр. 24 6.8. Preset Speed Setup Menu

    Screen 1. Speeds Menu Press > to enter 2. Speed 1 Name Speed 1 3. Speed 1 Duration 0:30 hours Buttons Used Comments <> Use > to enter Speeds Menu +<> Use to rename displayed speed Move to next menu item +<> Use to set duration of speed Move to next menu item Note: Each time a preset speed is…

23. Стр. 25 Buttons

    Used Comments 7. Power Usage 225W (1700W Max) Real-time display of pump power usage. 8. Drive Temperature 67ºC (110ºC Max) Real-time display of motor driver temperature. Event log Press + to view 9. +- Use + to view event log Note: For troubleshooting purposes, the Event Log will record the last…

24. Стр. 26 6.12. Remote Stop

    Screen 1. Remote Stop is engaged Note: The above message will be displayed when an installed remote stop switch is activated. For either model, the pump will remain stopped until the remote stop switch is deactivated. See section 5.5 for more detail. 7. Maintenance     Clean strainer basket…

25. Стр. 27 9. Shaft Seal Change Instructions

    IMPORTANT SAFETY INSTRUCTIONS PLEASE READ AND FOLLOW ALL INSTRUCTIONS When servicing electrical equipment, basic safety precautions should always be observed including the following. Failure to follow instructions may result in injury. WARNING – To reduce risk of injury, do not permit children to…

26. Стр. 28 9.6. Replacing the Motor Assembly

    13. Slide the motor assembly, with the diffuser in place, into pump/strainer housing, being careful not to disturb the diffuser gasket. 14. Fasten assembly to pump/strainer housing using the four (4) 5/16" x 1.75" bolts. (Be sure housing gasket is in place, and lubricated. Replace if damaged).…

27. Стр. 29 10.2. Parts Listing

    Ref. No. Part No. Description Qty. 1A SPX2300DLS Strainer Cover Kit (Includes Strainer Cover, Lock-Ring, O-Ring) 1 1B SPX2300DLSB Strainer Cover Kit for Biguanide Sanitizers (Includes Strainer Cover, Lock-Ring, O-Ring) NOT Pressure Testable 1 2 SPX2300Z4 Strainer Cover O-Ring 1 3 SPX2300M Strainer…

28. Стр. 30 11. Troubleshooting

    11.1. General Problems  Motor Will NOT Start: 1. Make sure the terminal board connections agree with the wiring diagram on the pump data plate label. 2. Be sure the pump is wired for the available field supply voltage (230VAC). 3. Check for and correct any improper or loose wiring connections; open…

29. Стр. 31

    Noisy Pump: 1. Air leak in suction piping, cavitations caused by restricted or undersized suction line or leak at any joint, low water level in pool, and unrestricted discharge return lines. Correct the suction condition or throttle return lines, if practical. Holding your hand over the return…

30. Стр. 32 11.2. Check System Messages

    Code Troubleshooting Check System DC voltage too high Indicates that the DC bus voltage has risen above 400 VDC. Verify that line voltage is within 10% (207-253 VAC) of pump rated voltage at the terminal block. Check System DC voltage too low Indicates that the DC bus voltage has dropped below 230…

31. Стр. 33 12. Warranty

    13. Product Registration DATE OF INSTALLATION INITIAL PRESSURE GAUGE READING (CLEAN FILTER) PUMP MODEL *Retain this Warranty Certificate in a safe and convenient location for your records Page 33 of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS MaxFlo VS 500 Pump IS23520VSP Rev-D

32. Стр. 34 THIS PAGE INTENTIONALLY LEFT BLANK

    Page 34 of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS MaxFlo VS 500 Pump IS23520VSP Rev-D

33. Стр. 35 THIS PAGE INTENTIONALLY LEFT BLANK

    Page 35 of 36 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS MaxFlo VS 500 Pump IS23520VSP Rev-D

34. Стр. 36 FCC Compliance Statement

    This device complies with part 15 of the FCC rules. Operation is subjected to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.