Инструкция на Система Big Multi

Текст инструкции

1. Стр. 1 INSTALLATION MANUAL

   Floor Console / R407C Under Ceiling Dual Type Refrigerant SPLIT TYPE AIR CONDITIONER (PART NO. 9363073010) This air conditioner uses new refrigerant HFC (R407C). For authorized service personnel only. WARNING! This mark indicates procedures which, if improperly performed, might lead to the death or…

2. Стр. 2 SELECTING THE MOUNTING POSITION

   Fig. 1 • Floor console Install at a place that can withstand the weight of the indoor and outdoor units and install positively so that the units will not topple or fall. Left Right 12" (30 cm) or more 12" (30 cm) or more (1) Do not install where there is the danger of combustible gas leakage. (2) Do…

3. Стр. 3 Name and Shape

   STANDARD PARTS Nylon fastener The following installation parts are furnished. Use them as required. INDOOR UNIT ACCESSORIES Description Q’ty Application Q’ty 1  AA CC  ƒƒ ÁÁ Ãà ,, @ B € ‚ À @ B € ‚ À  Cover plate (right) VT wire 1 1 Tapping screw (ø4 x 10) For fixing the drain hose Drain hose…

4. Стр. 4 1. PREPARING INDOOR UNIT INSTALLATION

   When the directions are selected, drill a 4” (10 cm) dia. hole on the wall so that the hole is tilted downward toward the outdoor for smooth water flow. When the pipe is led out from the rear, make a hole in Fig. 5, at the position shown. REMOVE THE INTAKE GRILLE Fig. 5 INSTALLATION PROCEDURE…

5. Стр. 5

   lower than the drain hose connecting port of the indoor unit. Fig. 9 OK Install the drain hose at the rear; it should not be installed on the top or right side. NO NO When the directions are selected, drill 3-1/8” (80 mm) and 2” (50 mm) or 6” (150 mm) dia. hole on the wall so that the hole is tilted…

6. Стр. 6 3. INSTALLING BRACKETS

   Fig. 19 Remove the hole cover. Install the brackets with nuts, washers and spring washers (Fig. 16). Fig.16 Arrange the drain hose lower than this portion. Drain hose NO OK Spring washer When drain hose is arranged backward. Secure the drain hose with the VT wire (Fig.20). Bracket Special nut Fig.20…

7. Стр. 7 2. BENDING PIPES

   When the flare nut is tightened properly by your hand, use a torque wrench to finally tighten it. The pipes are shaped by your hands. Be careful not to collapse them. Fig. 25 Fig. 22 Tighten with two wrenches. Wrench (fixed) Flare nut Torque wrench OK Extend the pipe by unwinding it. NO Indoor unit…

8. Стр. 8 5. CONNECTING AN INDOOR CAPILLARY TUBE

   4. GAS LEAKAGE INSPECTION Installation Procedure (1) Braze each part (connection pipe, indoor capillary tube, and branch liquid pipe) as shown in Fig. 27. (2) Wrap the two BR sheets around the indoor capillary tube as shown in Fig. 28. (3) Cover the indoor capillary tube and the branch liquid pipe…

9. Стр. 9 HOW TO FIX THE CONNECTION CORD

   2. IF TWO WIRES ARE CONNECTED TO ONE TERMINAL BLOCK. After passing the connection cord through the insulation tube, fasten it with the cord clamp. A. As a rule, round terminal should be used to connect to the terminal block. Fig. 34 (1) Cut the wire end with a wire cutter or wirecutting pliers, then…

10. Стр. 10 Fig. 36

    Electric component box 4. WIRING A. Simultaneous operation for buildings Fig. 39 Remote controller qwe Remove the four tapping screws. Do not remove the screws. If the stays are removed, the electric component box will fall. qwe qwe Indoor unit qwe qwe qwe qwe qwe qwe Master Slave Slave Slave RSTNE…

11. Стр. 11 2. MASTER/SLAVE SELECT SWITCH

    (1) Remove the cord clamp. (2) Process the end of the connection cords to the dimensions shown in Fig. 43. (3) Connect the end of the connection cord fully into the terminal board. Fig. 45 Fig. 43 Terminal board Indoor unit Printed circuit board SW2 0 Remote controller cord • For the master unit…

12. Стр. 12 Fig. 48

    9. TEST RUNNING Remote controller cord REMOTE CONTROLLER White Red Binder (small) • Supply power to the crankcase heater 12 hours before the start of operation in the winter. • For test running, when the remote controller FAN CONTROL button and MASTER CONTROL button are pressed simultaneously for…

13. Стр. 13 10. MOUNT THE COVER PLATE AND

    THE INTAKE GRILLE Table 5 1. MOUNT THE COVER PLATE (RIGHT) (1) Cut a pipe exit hole in the right plate. This is only when the pipe exits from the right side. (This operation is not required when the protrusion is on the top or rear.) Fig.52 Cover plate(right) (2) Join the cover plates (right) and…

14. Стр. 14 3. MOUNT THE INTAKE GRILLE

    (1) Cut the right side of the intake grille. This is only when the pipe exits from the right side (Fig. 55). Fig.55 (2) Insert the hinges on the bottom of the intake grille into the holes in the base assembly. Then mount the arms to the three areas on the top of the intake grille (Fig. 56). Fig.56…

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.