Технический каталог IMP PUMPS 2020 - Насосы CB, CBN, BL-H, DL

Текст каталога

1. Стр. 1

   CB, CBN, BL-H, DL TECHNICAL DATA IMPPUMPS | Technical Data 2020

2. Стр. 2 GENERAL INFORMATION

   ALL PRODUCTS AND COMPONENTS ARE MANUFACTURED FROM ENVIRONMENTALLY FRIENDLY MATERIALS. UPON DISPOSAL INTERNAL ENVIRONMENTAL REGULATION MUST BE CONSIDERED. FURTHER INFORMATION ON ALL PUMPING PROGRAMS WITH TECHNICAL DATA ARE AVAILABLE ON WWW.IMP-PUMPS.COM GENERAL SALES CONDITIONS AND TERMS OF PAYMENT…

3. Стр. 3 ABOUT US

   PRESENT IMP PUMPS is Slovenian manufacturer of pumps and pumping systems located in Komenda in Slovenia. Company designs, develops, manufactures, distributes and maintains pumps and pumping systems. With products and services of its own and from strategic partners, company is positioned as provider…

4. Стр. 4 Product overview

   The basic production program of IMP PUMPS are circulating pumps for HVAC application. Pumps are flanged or threaded and single or double design with a bronze or cast iron hydraulic casing. All cast iron hydraulics are covered with cataphoresis. Wet running circulating pumps NMT (electronic savings…

5. Стр. 5 RIGIDLY COUPLED

   CENTRIFUGAL PUMPS Handled Liquids Clean or slightly contaminated low viscosity liquids without solid & fibrous particles. Technical Data Discharge Flange DN 32 DN 150 mm Capacity up to 600 m³/h(*) Head up to 100 m(*) Operating Temperature -10 °C’ to +140 °C(** ) Casing Pressure (Pmax) 10 bar (16…

6. Стр. 6 Field Charts

7. Стр. 7 Installation Arrangements

   CB pumps can be installed in different arrangements R /3 R /0 R /6 Horizontal installation on ground Horizontal position on a base plate R /9 R/3 Suction Flange Position Direction of Rotation (R) Installation on perpendicular pipes Direction of rotation viewed from driver end: R : Right •Between two…

8. Стр. 8 Form: F1 (Slide - fit shaft application)

   Form: F2 (Slide - fit shaft application)

9. Стр. 9 Rigid Coupling Application

   For motor shaft diameters of Ø60 mm or bigger. Part List * Flushing 001 Volute Casing 005 Motor Pedestal 020* Wear Ring (casing) 021* Wear Ring (seal cover) 043 Mechanical Seal Cover 049 Mechanical Seal Spacer Sleeve 050 Impeller 060 Shaft 065 Impeller Nut and Washer 088 Thrower 093 Rigid Coupling…

10. Стр. 10 7L

    7E 7D 1.4460 1.4462 1.4301 1.4021+QT 1.4021 2.1096.01 2.0975.01 2.1050.01 1.4008 1.4469 1.4317 1.4409 1.4517 1.4408 1.4500 0.7040 Volute Casing Mechanical Seal Cover Impeller Shaft Bearing Housing Wear Ring Mech. Seal Spacer Sleeve Mechanical Seal (*) 1.4309 7S 8N 80 4C 4A 40 80 8T 60 1.4308 7L 8M…

11. Стр. 11 EN 733 NORM PUMPS

    Handled Liquids Clean or slightly contaminated low viscosity liquids without solid & fibrous particles. Technical Data Discharge Flange DN 32 DN 150 mm Capacity up to 600 m³/h(*) Head up to 100 m(*) Operating Temperature -10 °C’ to +140 °C(** ) Casing Pressure (Pmax) 10 bar (16 bar)(**) (Pmax…

12. Стр. 12 Field Charts

13. Стр. 13 Dimensions

14. Стр. 14 Form: F1 (Soft Packing Seal Pump)

    Form: F2 (Soft Packing Seal Pump)

15. Стр. 15 Form: F1 (Mechanical Seal Pump)

    049* 405* 043* Form: F2 (Mechanical Seal Pump) 049* 405* 043*

16. Стр. 16 Oil Lubrication Bearing Housing

    321* 034* 422* 410* 232* 410* 422* 231* 234* 016 034* 321* 320 Re-greasable Bearing Housing 321* 034* 034* 321* 016 320

17. Стр. 17 Part List

    * Flushing 421* 070* 020* 021* 001 Volute Casing 016 Support Foot 020* Wear Ring (Casing) 021* Wear Ring (Seal Cover) 030 Bearing Housing 034* Bearing Cover (GG) 035 Bearing Cover (St) 040 Soft Packing Seal Cover 042 Gland 043* Mechanical Seal Cover 046 Lantern Ring 049* Mechanical Seal Spacer…

18. Стр. 18

    1.4460 1.4404 1.4301 1.4021+QT 1.4021 7D 1.0503 8T 60 7L 7E 2.1096.01 2.0975.01 2.1050.01 1.4008 1.4317 1.4469 1.4517 1.4500 1.4409 1.4408 1.4309 1.0619 Volute Casing Seal Cover (Mech. or Soft) Impeller Shaft Bearing House Wear Ring Shaft Sleeve Mechanical Seal (*) 1.4308 20 60 6L 70 7L 8M 7D 7S 8N…

19. Стр. 19 MULTISTAGE

    CENTRIFUGAL PUMPS Handled Liquids Clean or slightly contaminated low viscosity liquids without solid & fibrous particles. Technical Data Discharge Flange DN 32 DN 250 mm Capacity up to 1000 m³/h Head up to 550 m Speed up to 2900 rpm Operating Temperature 10°C up to +140 °C* Casing Pressure (Pmax) 30…

20. Стр. 20

    40/2 40/3 40/4 40/5 40/6 Heavy Duty Design 32/3 32/4 32/5 32/6 32/7 32/8 40/7 32/9 40/9 40/8 13 40/12 40/11 40/10 40/ 32/14 32/13 32/12 32/11 32/10 4 1450 rpm 50/2 50/3 50/4 50/5 50/6 50/7 50/8 50/9 50/ 1 50/ 2 11 50/ 80/6 65/7 40 65/2 65/3 65/4 65/5 100 100/2 100/3 100/4 100/5 100/6 100/7 100/8…

21. Стр. 21 Field Chart

22. Стр. 23 Sectional Drawings

    BL-H - 80 - 100 - 125 - 150 - 200 - Series *020 030.1 030.2 *021.2 230 050 *021.1 Part List *020 *021.1 *021.2 030.1 030.2 * Optional Suction Casing Discharge Casing Stage Casing Diffuser Final Stage Diffuser Wear Ring (stage casing) Wear Ring (suction casing) Wear Ring (stage casing) Bearing…

23. Стр. 24 L

24. Стр. 26 Suction Casing

25. Стр. 27 DOUBLE SUCTION PUMPS

    Handled Liquids Clean or slightly contaminated low viscosity liquids without solid & fibrous particles. Technical Data Discharge Flange DN 65 DN 600 mm Capacity up to 6000 m³/h Head up to 180 m Speed up to 2900 rpm Operating Temperature -10 °C’ to +110 °C* Casing Pressure (Pmax) 16 bar - 25 bar*…

26. Стр. 28

    1450 rpm 50 65-250 100 80-200 80-250 80-315 150 200 100-250 100-315 100-400 400 200-315 200-400 200-500 150-450 500 150-315 Capacity (m³/h) 300 125-315 125-350 125-450 150-600 1000 300-315 250-350 250-450 250-600 300-700 1500 350-350 300-400 2000 300-500 350-400 3000 350-500 350-700 4000 Grouped…

27. Стр. 30 Sectional Drawings

    * Mechanical Seal Application 231.1 050 231.2* *405 *048 *422 Part List * Stuffing Box Volute Casing (top half) Volute Casing (bottom half) Wear Ring Bearing Bracket Bearing Cover (inboard) Bearing Cover (outboard) Bearing Cover (coupling) Stuffing Box Gland Lantern Ring Mechanical Seal Cover…

28. Стр. 31 l3

29. Стр. 32 Volute Casing(**)

    Impeller Shaft Bearing Housing Wear Ring (Casing) Shaft Protecting Sleeve Mechanical Seal (*) 7L 7E 7D 1.4460 1.4462 1.4301 1.4021+QT 1.4021 2.1096.01 2.0975.01 2.1050.01 1.4008 1.4469 1.4317 1.4409 1.4517 1.4408 1.4500 0.7040 1.4309 7S 8N 80 4C 4A 40 80 8T 60 1.4308 7L 8M 7D 1.0619 70 0.7043 30 3S…

30. Стр. 33 THE HONEST PRODUCT

    FOR THE HONEST PRICE IMP PUMPS d.o.o. Pod hrasti 28 1218 Komenda SLOVENIA E: info@imp-pumps.com T: +386 F: +386 www.imp-pumps.com 12.2.2020 Contact: © IMP PUMPS d.o.o.

Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.