Инструкция на Полупромышленные сплит-системы UU37W~61W, UU12W~60W
Инструкция по эксплуатации
Смотрите также: Коды ошибок: 19 кодов →
Загружаем документ…
Текст инструкции
-
ITALIANO
ESPAÑOL FRANÇAIS DEUTSCH INSTALLATION MANUAL AIR CONDITIONER • Please read this installation manual completely before installing the product. • Installation work must be performed in accordance with the national wiring standards by authorized personnel only. • Please retain this installation manual…
-
This symbol indicates the possibility of death or serious injury
This symbol indicates the possibility of injury or damage to properties only. n The meanings of the symbols used in this manual are as shown below. Be sure not to do. Be sure to follow the instruction. n Installation Always perform grounding. Donʼt use a power cord, a plug or a loose socket which is…
-
Do not install the product at a place that there
is concern of falling down. Use caution when unpacking and installing. • Otherwise, it may result in personal injury. • Sharp edges may cause injury. n Operation Do not share the outlet with other appliances. Do not use the damaged power cord. Do not modify or extend the power cord randomly. • It…
-
n Installation
Install the drain hose to ensure that drain can be securely done. Install the product so that the noise or hot wind from the outdoor unit may not cause any damage to the neighbors. • Otherwise, it may cause water leakage. • Otherwise, it may cause dispute with the neighbors. Always inspect gas…
-
1. Installation Places
-
Install the branch pipe so that pipe length and difference between high and low will not exceed
-
3. Synchro Combination table
-
5) Press
-
Electrical Wiring
-
Outdoor
unit Indoor unit CAUTION The power cord connected to the outdoor unit should be complied withIEC 60245 or HD 22.4 S4 (This equipment shall be provided with a cord set complying with the national regulation. 1 Phase(Ø) GN /YL 20 mm Model Phase(Ø) UU18W/24W/30W 1 UU36W/UU42W 1 /UU48W/UU60W UU37W/UU43W…
-
Connecting the cable to Outdoor Unit
• Remove the side panel for wiring connection. • Use the cord clamp to fix the cord. • Earthing work - Connect the cable of diameter more to the earthing terminal provided in the control box and do earthing. Connecting cable terminal Power cord terminal Cord clamp Cord clamp * Make sure the rubber…
-
Preparation of Piping
Main cause of gas leakage is defect in flaring work. Carry out correct flaring work in the following procedure. Copper tube Slanted Uneven Rough 90 Cut the pipes and the cable. • Use the accessory piping kit or the pipes purchased locally. • Measure the distance between the indoor and the outdoor…
-
Connecting the pipes to the Outdoor unit
• Align the center of the piping and sufficiently tighten the flare nut by hand. Continuous • Finally, tighten the flare nut with torque wrench until the wrench clicks. - When tightening the flare nut with torque wrench, ensure the direction for tightening follows the arrow on the wrench. Outside…
-
<Figure 2>
Knock-out Preventing foreign objects from entering (Figure3) ENGLISH • When connecting in a downward direction, knock out the knock-out hole of the base pan. (refer to figure 2) Base pan <Figure 3> Liquid side piping • Plug the pipe through-holes with putty or insulation material(procured locally)to…
-
Seal a small
opening around the pipings with gum type sealer. Forming the piping Form the piping by wrapping the connecting portion of the indoor unit with insulation material and secure it with two kinds of vinyl tape. • If you want to connect an additional drain hose, the end of the drain outlet should be…
-
Leakage test and Evacuation
Air and moisture remaining in the refrigerant system have undesirable effects as indicated below. 1. Pressure in the system rises. 2. Operating current rises. 3. Cooling(or heating) efficiency drops. 4. Moisture in the refrigerant circuit may freeze and block capillary tubing. 5. Water may lead to…
-
Leakage test and Evacuation
Evacuation 1. Connect the charge hose end described in the preceding steps to the vacuum pump to evacuate the tubing and indoor unit. Confirm the "Lo and Hi" knob of the manifold valve is open. Then, run the vacuum pump. The operation time for evacuation varies with tubing length and capacity of the…
-
Test running
CAUTION: After the confirmation of the above conditions, prepare the wiring as follows: 1) Never fail to have an individual power specialized for the air conditioner. As for the method of wiring, be guided by the circuit diagram pasted on the inside of control box cover. 2) Provide a circuit breaker…
-
Function
ENGLISH Function Forced Cooling Operation • Adding the refrigerant in winter. Setting Procedure 1) Set the Dip Switch as follow after shutting the power source down. 6 UU18W UU24W UU30W UU36W UU42W UU48W UU60W UU37W UU43W UU49W UU61W 2) Reset the power. 3) Red LED and Green LED of PCB lights during…
-
Self-diagnosis Function
Self-diagnosis Function Error Indicator (Outdoor) 2 Times 2 Times Outdoor Error Ex) Error 21 (DC Peack) 2 Times LED01G (RED) 1 Sec. 1 Sec. 1 Time 1 Sec. 1 Time 1 Time LED02G (GREEN) 2 Sec. 2 Sec. UU18W/24W/30W Error Code UU36W/42W/48W/60W Description LED 1 (Red) UU37W/43W/49W/61W LED 2 (Green)…
-
Installation Guide at the Seaside
CAUTION: 1. Air conditioners should not be installed in areas where corrosive gases, such as acid or alkaline gas, are produced. 2. Do not install the product where it could be exposed to sea wind (salty wind) directly. It can result corrosion on the product. Corrosion, particularly on the condenser…
Схемы, таблицы и рисунки — в просмотре документа выше. Клик по номеру страницы открывает её в просмотре.